C-JC-0201BTXN 133 69

C-JC-0201B; CIB, 1x jalousie actor (2xRO with dependent switching, local function). 230VAC/16A, 2x DI

DI 2x DI
DO 1 shutter / motor output
AI
AO
COM 1x CIB slave
SENSOR
Picture Variant Variant description
C-JC-0201B
C-JC-0201B is a module on the CIB bus that contains
- 2 relay outputs interlocked, each separately connected to the terminal board
- 2 binary inputs for connection of potential-free contacts, which evaluate short and long presses.
When the CIB master is not connected or not communicating, the outputs can be controlled manually if the control contacts are connected directly to the module inputs.
The module is mechanically designed in the "box" type for mounting in the installation box.
Order num. TXN 133 69
Teco code TXN 133 69
Categories CFox - Built-in modules
Tags -
COM - System buses
Installation I/O Bus CIB 1x CIB slave
DI - Features of digital DC inputs (1)
Number of inputs in group 1
Input type active (for dry contacts connection)
Galvanic separation of inputs from CIB bus No
Max. measuring voltage on the connected contact 3,3 V DC
Internal input resistance 2 kΩ
Max. resistance for closed contact, log. 1 < 0,5 kΩ
Min. resistance for open contact, log. 0 > 1,5 kΩ
RO - Parameters of binary relay outputs (1)
Parameters valid for the terminals DO1u, DO1d
Number of relay outputs 2
Number of output groups 1
Number of outputs in group 2
Output type electromechanical relay, unprotected output
Contact type Up-0-Down, three-state actuator
Galvanic separation from internal circuits Yes
Diagnose Alarm signaling on panel module
Switching voltage 300 V max., 5 V min.
Switching current 16 A max., 100 mA min.
Switching power 4000 VA max., 384 W max.
Short-circuit protection No
Contact closing time typ. 15 ms
Contact opening time typ. 5ms
Reverse delay 300 ms
Mechanical life min. 20 000 000 cycles
Electrical life at rated load min. 50,000 switchings
Treatment of inductive load External RC element, varistor (AC), diode (DC)
Insulation voltage between outputs and internal circuits 4000 V AC
Isolation voltage between groups of outputs to each other 4000 V AC
Insulation voltage between contacts 1000 V AC
Power supply
Supply voltage, tolerances 24/27 V DC from CIB bus
Power supply from CIB - maximum current consumption (mA) 33 mA
Galvanic separation of power supply from internal circuits No
Internal protection Yes, PTC reversible fuse
Operating conditions, product standards
Product standard ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)
Protection class of electrical object III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) IP20
Operating areas Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation II, acc. ČSN EN 60664-1:2004 (mod IEC 606641:1992)
Type of device In the installation box, under the cover
Working position Any
Type of operation (operating frequency) Continuous
Ambient temperature operating range -20 °C to + 55 °C
Operating temperature maximum (° C) +55°C
Operating temperature minimum (° C) -20°C
Storage temperature range –25 °C to +70 °C
Relative humidity from 10 % up to 95 % without condensation
Atmospheric pressure min. 70 kPa (< 3000m. at sea)
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission B, according to EN 55022: 1999 (mod CISPR22: 1997)
Electromagnetic compatibility / Immunity min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Installation
Description Relay module C-JC-0201B can be mounted in any position in
installation box under the lid or under the device in the installation box
boxes. The installation is performed according to TXV 004 13.
Attention! The device may contain parts with dangerous voltages, covers being removed, or cabling manipulated, or disconnect the appropriate circuits or turn off the power !.
Connection
Connection description The C-JC-0201B module has a CIB bus and 2 inputs are connected to screw terminals, the relay contacts for the control of blinds are connected by means of insulated conductors with a length of approx. 80 mm terminated in sockets. The number of modules on the line is limited by the maximum allowed line current. Further information can be found in the manual Peripheral modules on the CIB TXV 004 13.
An example of module connection is shown in the following figure.
Connection of power and system communication terminal block with screw terminal 1.5 mm2
Specific I / O Blind / motor output - Up and Down contacts
Connection of specific I / O Insulated wires with sleeve
Module installation tools (-) 3 mm, flat screwdriver
Module operation
Commissioning The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module.
Module diagnostics The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment. When the power is turned on, the RUN LED lights up green, after communication is established, it starts flashing. The switching status of the relay is indicated by a green LED.
Maintenance
Description The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Notice Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.

HW documentation

PDF

C-JC-0201B - Basic documentation

120.37 kB
PDF

C-JC-0201B - Basic documentation

1.10 MB, (EN)

User manuals

PDF

Peripheriemodule am CIB-Common Installation Bus(R) (cs)

13.18 MB
PDF

Peripheral modules on the CIB Common Installation Bus(R) (en)

4.66 MB

Files for designers

DWG

C-JC-0201B - technical drawing M01 DWG

67.35 kB
DXF

C-JC-0201B - M01 DXF technical drawing

130.73 kB
DWG

C-JC-0201B - S01 DWG technical drawing

43.19 kB
DXF

C-JC-0201B - S01 DXF technical drawing

41.62 kB

EC - Declaration of Conformity

PDF

Foxtrot - EC Declaration of conformity

295.20 kB
  • C-JC-0201B, a module for blinds control - The C-JC-0201B module is equipped with one output intended for standard blinds control - i.e. the so-called three-point-control: opening-idle-closing. The module can also be used for three-point valve control, etc. The module is internally eq...
  • Control of Velux roof windows - ...nsions are 49 x 47 x 28 mm and it is powered by 230 VAC. Fig. 1. Connecting the Velux KLF 050 module to the C-JC-0201B blinds module   Notes: In this connection, the “up” position (switched DO1...
  • Control of asynchronous motors for blinds and awnings, the C-JC-0202B - ...with reversing by switching the windings (similar to 3-point actuators for valves and dampers) we have a specialized module C-JC-0201B designed to control one louver and place it in the installation box near the shading element or directly in the l...

No data available.