English
C-DM-0006M-ILEDTXN 133 46
C-DM-0006M ILED; CIB, 6 channel dimmer module for LED chip, current source
| DI | |
|---|---|
| DO | |
| AI | |
| AO | 6x LED Chip Dimmer |
| COM | 1x CIB slave |
| SENSOR |
| Picture | Variant | Variant description |
|---|---|---|
|
C-DM-0006M-ILED |
The C-DM-0006M-ILED module is a 6-channel controlled current source for direct control of the brightness of LED chips, ie continuous dimming 0-100% in adjustable ranges of 150 mA, 350 mA, 500 mA, 700 mA, which it generates from an external power supply 48 VDC / 5A. Each channel can be controlled separately. It can also be used as a two-channel RGB actuator, or for two-channel control of the chromaticity of white lighting, etc.
The module is designed for a DIN rail switchboard and is connected to the basic module via a two-wire CIB Common Installation Bus®.
The module is designed for a DIN rail switchboard and is connected to the basic module via a two-wire CIB Common Installation Bus®.
| Order num. | TXN 133 46 |
|---|---|
| Teco code | TXN 133 46 |
| Categories | CFox - Modules on DIN rail |
| Tags | - |
| COM - System buses | |
|---|---|
| CIB - Common Installation Bus (R): Installation I/O bus | 1x CIB slave |
| AO - Analog output parameters | |
| Number of analog outputs | 6 |
| The number of groups of analogue outputs | 2 |
| Number of outputs in group | 3 |
| Parameters valid for the terminals | LED1 - LED6 |
| Power supply | |
| Supply voltage, tolerances | 24/27 V DC from CIB bus |
| Module thermal/power loss | 5 W |
| Power supply from CIB - maximum current consumption (mA) | 17 mA |
| Size and weight | |
| Weight approx. | 125 g |
| Product dimensions (width x height x depth) | 52 x 90 x 58 mm |
| Operating conditions, product standards | |
| Product standard | ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999) |
| Protection class of electrical object | I, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016) |
| IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) | IP20 |
| Operating areas | Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005) |
| Degree of pollution | 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007) |
| Overvoltage category installation | II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007) |
| Type of device | Module on DIN rail |
| Working position | Any |
| Type of operation (operating frequency) | Continuous |
| Ambient operating temperatures | 0 ° C to + 55 ° C |
| Operating relative humidity | from 10 % up to 95 % without condensation |
| Operating atmospheric pressure | min. 70 kPa (<3,000 m above sea level) |
| Storage temperatures | –25 °C to +70 °C |
| Electromagnetic compatibility, Mechanical endurance | |
| Electromagnetic compatibility / Emission | B, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015) |
| Electromagnetic compatibility / Immunity | min. according to ČSN EN 60730-1 ed.2: 2001 |
| Sinusoidal vibration endurance | 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.) |
| Packaginng, transportation, storage | |
| Description | The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C |
| Connection | |
| Connection of power and system communication | connector with 2.5 mm2 screw terminal |
| Connection of inputs / outputs | connector with screw terminal 2.5 mm2 |
| Module installation tools | (-) 3 mm, flat screwdriver |
| Module connection | The supply voltage of 4.5 - 48 V must be selected with regard to the LED light sources used. The greater the difference between the source voltage and the voltage of the LED lights, the greater the power loss of the module and the greater the cooling problem. The outputs for LED light sources have a common positive supply pole (anode) marked as LED +. The maximum current of one terminal 10 A must be observed for the LED + outputs. An example of the module connection is shown in the following figure. |
| Module operation | |
| Commissioning | The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module. |
| Module diagnostics | The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment. |
| Maintenance | |
| Description | The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected. |
| Notice | Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!! |
| Warranty | |
| Generally | Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s. |
| Notice | You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change. |
HW documentation
C-DM-0006M-ILED - Basic documentation
989.87 kB, (EN)
User manuals
Peripheral modules on the CIB Common Installation Bus(R) (en), TXV00413_02
13.94 MB, (EN, RU, DE, UA)
Scheme
C-DM-0006M-ILED
61.73 kB
C-DM-0006M-ILED
66.33 kB
Files for designers
Foxtrot 2 - library of elements in DXF and DWG formats, v. 2024/01.
20.49 MB
Foxtrot 2 - element library for SchemataCAD, v. 2024/01
6.79 MB
EC - Declaration of Conformity
Foxtrot - EC Declaration of conformity
295.20 kB, (EN, RU, DE, UA)
- C-DM-0006M-ILED - ....g. the MeanWell DR-60-12. For a similar example, see Chapter 6.4.2 An example of dimming power LED CREE chips using the C-DM-0006M-ILED module . The outputs for LED light sources have a common positive power pole (anode) labelled as LED...
- Dimming of LED ceiling panels with a current of 1 A, module C-DM-0006M-ILED - ...r supply with this output, which is a standard part of the luminaire package, and we will connect the panel directly to the C-DM-0006M-ILED dimmer outputs (hereinafter in the text C-DM). The C-DM module is equipped with outputs with a maxi...
- An example of dimming the CREE power LED chips by the C-DM-0006M-ILED module - ...ry to correctly dimension the power supply for the LEDs. The requirements for the LED power supply The C-DM-0006M-ILED dimmer enables powering from the 4.5 ÷ 48 VDC power supply, with a maximum current consumption...
- Power dissipation of modules for calculation of switchboard heating - ...for LED strips 12-24VDC, max. 4A/channel C-DM-0006M-ULED 5,0 W TXN 133 46 C-DM-0006M-ILED; CIB, 6 channel dimming module for LED chips, controlled power supply C-DM-0006M-ILED 5,0 W...
- C-DM-0006M-ULED - ...he C-DM-0006M-ULED module, as the LEDs could be destroyed! These LED strips powered by nominal current must be dimmed by the C-DM-0006M-ILED module. Powering the LEDs 12 or 24 VD...
- Dimming LEDs with a nominal current of 150, 350, 500 or 700 mA - ...ol of current-powered LED sources with nominal supply current of 150 mA, 350 mA, 500 mA or 700 mA, there is available the C-DM-0006M-ILED module. Each output can be set individually and independently. The supply voltage for LED coming from an e...
- Dimming LEDs powered from a current source - ...vide; 300 lm), CRI up to 80. LED power supplies , for which you can use dimmers with rated current, e.g. C-DM-0006M-ILED ), are used more and more frequently. Large portion of LED lights (e.g. large-area LED panels, ceiling...
- Basic information, concepts - lighting and light sources - ...EDs supplied with rated current (typ. 350, 500, 700, 1000 mA). Dimmable with controllable power supply, see module C-DM-0006M-ILED . Switching of sources for current-excited LEDs see this article . Dimming current-excited...
- DR-60-24 power supply - The DR-60-24 power supply is a mains switch-mode power supply with 24 V continuous output voltage and 2.5 A. It is designed to supply power to the Foxtrot control systems without a backup. Basic properties are identical with the DR-60-12 power supp...
No data available.