English
C-EM-0100MTXN 143 40
C-EM-0100M; CIB, 1 phase electricity meter 230 V AC
| DI | |
|---|---|
| DI/AI | 1x DI/AI |
| DO | |
| AI | |
| AO | |
| COM | 1x CIB slave |
| SENSOR |
| Picture | Variant | Variant description |
|---|---|---|
|
C-EM-0100M |
Module of a 1-phase 4-quadrant electricity meter providing all parameters of consumed and supplied energy. The measurement is indirect, the current is sensed by a current transformer according to the required input range. The data is transmitted via a two-wire CIB - Common Installation Bus®
| Order num. | TXN 143 40 |
|---|---|
| Teco code | TXN 143 40 |
| Categories | CFox - Modules on DIN rail, Electricity meters |
| Tags | - |
| COM - System buses | |
|---|---|
| CIB - Common Installation Bus (R): Installation I/O bus | 1x CIB slave |
| DI - Organization of binary inputs | |
| Total number of binary inputs | 1 |
| Number of groups of binary inputs | 1 |
| DI - Parameters of binary inputs DC | |
| Number of inputs in group | 1 |
| Common wire | GND - module ground |
| Galvanic separation of inputs from CIB bus | No |
| AI - Organization of analog inputs | |
| Total number of analog inputs | 1 |
| Number of inputs per group | 1 |
| Input type | AI / DI - combined |
| Common wire | GND terminal |
| Galvanic separation from internal circuits | No |
| AI - Analog Input Ranges | |
| Passive sensor | Pt1000, W100 = 1,385 (-90 to +320 °C) |
| Passive sensor | Pt1000, W100 = 1,391 (-90 to +320 °C) |
| Passive sensor | Ni1000, W100 = 1,500 (–60 to +200 °C) |
| Passive sensor | Ni1000, W100 = 1.617 (-60 to +200 °C) |
| Passive sensor | Resistance transmitter 0-160 kOhm |
| Passive sensor | KTY81-121; (-55 to + 125 °C) |
| Passive sensor | NTC Thermistor 12k / 25 °C (-40 to + 125 °C) |
| Measurement of supply network parameters - frequency | |
| Nominal frequency | 50/60 Hz |
| Frequency range | 45 - 65 Hz |
| Measurement of supply network parameters - voltage | |
| Rated voltage UNOM (UDIN) | 180–250VAC |
| Crest factor in UNOM | 2 |
| Measuring range, phase voltage (UL-N) | 20÷450 V AC |
| Voltage measurement accuracy | ± 10% of value or ± 1% of range |
| Measurement category | 300V CAT II |
| Input impedance | 0,7 MΩ |
| Input consumption | max. 0,09 VA |
| Permanent overload (UL-N) | 1000 V AC |
| Peak overload, for 1 s (UL-N) | 1300 V AC |
| Measurement of supply network parameters - currents | |
| Method for measuring current | indirect via current transformer |
| Nominal current of transformer Inom | N * 0,05 A AC, max 65 A AC |
| Crest factor at Inom | 1,8 |
| Current measurement accuracy | ±10% of value or ±1% of range |
| Input impedance | 3 Ω |
| Input consumption | max. 8 mVA |
| Permanent overload | 0,25 A AC |
| Peak overload, for 5 s, repetition period min. 60 s | 0,36 A AC |
| Measurement of supply network parameters - other quantities | |
| Active power, measuring range (PNOM = UNOM × INOM×cosφ); [W, V, A] | limited by measured voltage and current ranges |
| Reactive power, measuring range (QNOM = UNOM × INOM×sinφ); [VA, V, A] | limited by measured voltage and current ranges |
| Accuracy of active or reactive power (A) | ±10% of value or ±1% of range |
| Power supply | |
| Supply voltage, tolerances | 24/27 V DC from CIB bus |
| Power supply from CIB - typical current consumption (mA) | 15 mA |
| Internal protection | No |
| Size and weight | |
| Weight approx. | 53 g (65 g of double-sided proud transformative transformer) |
| Product dimensions (width x height x depth) | 23 x 90 x 58 mm |
| Module width in multiples of M (17.5 mm) | 1,5M |
| Operating conditions, product standards | |
| Product standard | ČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units |
| Protection class of electrical object | II, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016) |
| IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) | IP20 |
| Operating areas | Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005) |
| Degree of pollution | 2, according to ČSN EN 60664-1 ed.2: 2008 (idt IEC 60664-1: 2007) |
| Overvoltage category installation | II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007) |
| Type of device | Module on DIN rail |
| Working position | Vertical |
| Type of operation (operating frequency) | Continuous |
| Ambient operating temperatures | -20 °C to + 55 °C |
| Operating relative humidity | from 10 % up to 95 % without condensation |
| Operating atmospheric pressure | min. 70 kPa (<3,000 m above sea level) |
| Storage temperatures | –25 °C to +70 °C |
| Electromagnetic compatibility, Mechanical endurance | |
| Electromagnetic compatibility / Emission | A, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015) |
| Electromagnetic compatibility / Immunity | min. according to ČSN EN 60730-1 ed.3: 2012 |
| Sinusoidal vibration endurance | 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.) |
| Packaginng, transportation, storage | |
| Description | The module is packed in a cardboard box. The product must not be exposed to direct weather conditions during transport and storage. The product must only be stored in clean rooms free from conductive dust, aggressive gases and vapours. The most suitable storage temperature is 20 °C. |
| Installation | |
| Assembly description | The module is mounted in a vertical position on the U-rail ČSN EN 50022. Installation of the assembly (basic module and possibly peripheral modules) is performed according to TXV 004 13. |
| Connection | |
| Connection description | The module is connected via screw terminals. The measured voltage is connected to terminal U via a suitable fuse with characteristics according to the environment (e.g. a fuse with a value of 0.05 A) and the neutral conductor to terminal N. To connect the current measurement, it is necessary to use a measuring current transformer with such a conversion ratio that the output current in the required measurement range is up to 0.05A AC and with the corresponding insulation voltage, or the transformer must be installed on an insulated primary conductor with the corresponding insulation voltage. The secondary winding of the transformer is connected to terminals S1 and S2. The CIB bus is connected to terminals CIB+ and CIB–. |
| Connection of power and system communication | terminal block with screw terminal 0,2 - 2,5 mm² |
| Connection of inputs / outputs | terminal block with screw terminal 0,2 - 2,5 mm2 |
| Module operation | |
| Commissioning |
The module is operated, set up and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module. Attention: When working with the module, it is necessary to observe all necessary measures to protect people and property from injury and damage by electric current! The module must be operated by a person with the prescribed qualifications for such activity and this person must be thoroughly familiar with the principles of working with the module. If the module is connected to parts that are under dangerous voltage, it is necessary to observe all necessary measures to protect users and equipment from electric shock. The worker performing installation and/or maintenance of the device must be equipped with and use personal protective equipment and other safety equipment during work. If the module is used in a manner not specified by the manufacturer, the protection provided by the module may be reduced. Further information can be found in the manual Peripheral modules on the CIB bus, order no.: TXV 004 13.01. |
| Module diagnostics | Basic diagnostics are performed internally and the measurement results are available in the relevant registers of the Mosaic environment. The module status is indicated by the green RUN LED located on the front panel below the CIB bus connection terminals. After the CIB bus is connected, the green RUN LED lights up, indicating the presence of supply voltage on the CIB interface. After the module has established communication with the central unit, the RUN LED flashes. This means that the module is ready for operation. |
| Maintenance | |
| Description | The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected. |
| Notice | Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!! |
| Warranty | |
| Generally | Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s. |
| Notice | You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change. |
User manuals
Peripheral module on CIB-Common Installation Bus(R) (cs), TXV00413_01
14.01 MB
Peripheral modules on the CIB Common Installation Bus(R) (en), TXV00413_02
13.94 MB, (EN, RU, DE, UA)
HW documentation
Basic documentation C-EM-0100M
580.84 kB, (EN)
EC - Declaration of Conformity
Foxtrot 2 - EC Declaration of conformity (en)
590.59 kB, (EN, RU, DE, UA)
Files for designers
Foxtrot 2 - element library for SchemataCAD, v. 2025/08.
6.96 MB
Foxtrot 2 - library of elements in DXF and DWG formats, v. 2025/08.
21.80 MB
No data available.
No data available.