English
UC-1203TXN 112 03
UC-1203; MP-bus, communication module for Belimo servo drives
| DI | |
|---|---|
| DO | |
| AI | |
| AO | |
| COM | 1x TCL2 slave 1x MP bus |
| SENSOR |
| Picture | Variant | Variant description |
|---|---|---|
|
UC-1203 |
UC-1203; MP-bus, communication module for Belimo actuators
The UC-1203 module is used to connect Belimo control drives via the MP-Bus (Belimo company bus) to the basic Tecomat Foxtrot module via the TCL2 system communication bus. The module allows to connect up to 8 control actuators to the MP-Bus - actuators of lift valves and actuators of control ball valves. In addition, an external sensor (active / passive) can be connected to some drives, which is also processed by the UC-1203 module.
Operation of one connected drive takes approx. 700ms, ie. operation of all 8 drives takes approx. 5.6s. When operating the drives, this considerable time delay must be taken into account in the application program.
The UC-1203 module is used to connect Belimo control drives via the MP-Bus (Belimo company bus) to the basic Tecomat Foxtrot module via the TCL2 system communication bus. The module allows to connect up to 8 control actuators to the MP-Bus - actuators of lift valves and actuators of control ball valves. In addition, an external sensor (active / passive) can be connected to some drives, which is also processed by the UC-1203 module.
Operation of one connected drive takes approx. 700ms, ie. operation of all 8 drives takes approx. 5.6s. When operating the drives, this considerable time delay must be taken into account in the application program.
| Order num. | TXN 112 03 |
|---|---|
| Teco code | TXN 112 03 |
| Categories | Foxtrot - Communication Modules (TCL2) |
| Tags | - |
| COM - Serial channels | |
|---|---|
| MP-BUS - high level | 15 V typ.; 11 V min.; 18 V max. |
| MP-BUS - low level | 2.5 V max. |
| MP-BUS - short-circuit current | 10 mA max. |
| MP-BUS - communication speed | 1200 baud |
| MP-BUS - byte structure | 1 start, 8 data, 1 stop, no parity |
| MP-BUS - data transfer | bidirectional, half duplex |
| MP-BUS - Securing the transmission | 16 bit check sum |
| MP-BUS - Number of connectable slaves | 8 |
| COM - System buses | |
| TCL2 - system I/O bus | 1x TCL2 slave |
| Connection of Belimo drives | |
| Description |
The Belimo drives are connected to the UC-1203 module using 24V ~ / GD / MP terminals. The UC-1203 module does not provide power for controlled drives, the drives must be powered by an external 24V AC / DC power supply (s). Dimensioning of the power supply, maximum bus length, bus topology and conductor cross-sections for the MPBus bus, see Belimo company documentation. |
| Power supply | |
| Supply voltage, tolerances | 24 V DC, +25%, -15%, SELV |
| Maximum power input | 2,5 W |
| Module thermal/power loss | 2,5 W |
| Galvanic separation of power supply from internal circuits | No |
| Size and weight | |
| Weight approx. | 75 g |
| Product dimensions (width x height x depth) | 18 x 90 x 58 mm |
| Module width in multiples of M (17.5 mm) | 1M |
| Operating conditions, product standards | |
| Product standard | ČSN EN 61131-2: 2005 (idt IEC61131-2: 2003) - Programmable control units |
| Type of device | Module on DIN rail |
| Working position | Any |
| Ambient operating temperatures | -20 °C to + 55 °C |
| Storage temperatures | –25 °C to +70 °C |
| Electromagnetic compatibility, Mechanical endurance | |
| Electromagnetic compatibility / Emission | A, according to EN 55022: 1999 (mod CISPR22: 1997) |
| Emmisions - note | In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action. |
| Electromagnetic compatibility / Immunity | min. as required by EN 61131-2: 2007 |
| Sinusoidal vibration endurance | 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.) |
| Packaginng, transportation, storage | |
| Description | The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C |
| Installation | |
| Assembly description | Module is mounted in a vertical position on the U-rail ČSN EN 50022. Assembly installation (basic module and possibly peripheral modules) is performed according to TXV 004 10.01. |
| Connection | |
| Connection description |
The interface connection circuits of the TECOMAT Foxtrot PLC are connected to terminals A1 to A3 of the terminal block marked TCL2 +, TCL2-, GND. On the PLC side, the TCL2 communication line is terminated inside the PLC. On the side of the UC-1203 module, it is necessary to terminate the line. Termination is performed using a KB-0290 terminator (TXN 102 90) connected between the TCL2 + and TCL2- terminals. This terminator is part of the Tecomat Foxtrot PLC package. If there are other modules on the TCL2 communication line, termination is always performed at the end of the entire line! |
| Connection of power and system communication | terminal block with screw terminal 2.5 mm2 |
| Module operation | |
| Module diagnostics | The basic diagnostic system of the module is a part of its standard software. It operates from module power on and operates independently of the user. Diagnostic error states of the module and connected peripheral modules of the assembly are signaled |
| Module diagnostics |
Indications on the panel There are two indicator LEDs on the front panel of the module, RUN and MP. If the green RUN LED is lit, the module is in HALT mode (does not operate drives), if the RUN LED is flashing, the module is in RUN mode (operates drives). If the MP LED lights up red or flashes red, it indicates a communication fault with one of the operated drives. If the MP LED is green, communication with all drives is faultless. |
| Maintenance | |
| Description | The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected. |
| Notice | Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!! |
| Warranty | |
| Generally | Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s. |
| Notice | You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change. |
HW documentation
UC-1203 - Basic documentation
569.84 kB, (EN)
Files for designers
Foxtrot 2 - library of elements in DXF and DWG formats, v. 2024/01.
20.49 MB
Foxtrot 2 - element library for SchemataCAD, v. 2024/01
6.79 MB
EC - Declaration of Conformity
Foxtrot - EC Declaration of conformity
295.20 kB, (EN, RU, DE, UA)
- UC-1203, a module for connecting the MP-Bus actuators - The UC-1203 module is used for connecting Belimo regulating actuators via the MP-Bus (a Belimo company product). The module makes it possible to connect up to 8 regulating actuators (globe valves actuators, and regulating ball valves actuators) on...
- Power dissipation of modules for calculation of switchboard heating - ...111 81 SX-1181, converter M-bus - RS-232 SX-1181 1,0 W TXN 112 03 UC-1203; MP-bus, communication module for Belimo actuators UC-1203 2,5 W TXN 112 04...
- Ventilation and recuperation units - ...modules, e.g. C-HM-0308M Servo-drive with the MP-Bus protocol UC-1203 Further it is possible to control electrical heating (16 A relay outputs, e.g. the...
- Heating servo-drives and valves control - To control and regulate heating, cooling and similar systems, various types of valves are used: based on their function there are two-way, three-way and centre valves. There are valves with only basic function ON/OFF or switching, or there are co...
No data available.