R-SL-0201L-A, relay module and PWMTXN 132 43.A

R-SL-0201L-A; RFox2, 2x AI/DI, 1x RO-800A NO contact, radio type A

DI 2x AI/DI
DO 1x RO
1x PWM
AI 2x AI / DI, see DI
AO
COM 1x RFox2 slave
SENSOR Current
Picture Variant Variant description
R-SL-0201L-A, relay module and PWM
R-SL-0201L is a module designed for remote control of a street lamp in the RF network of the RFox II system. The module contains 1x relay output for switching the power source of the lamp, PWM output for brightness control, lamp internal current measurement and 2x AI/DI input. The module can be used for switching general loads, see parameters in the documentation.
Order num. TXN 132 43.A
Teco code TXN 132 43.A
Categories RFox2 - DIN Rail Modules
Tags -
COM - Wireless network
RFox2 wireless network RFox2 Slave
Communication frequency band 868,1 MHz
Transmission power +14 dBm
Input sensitivity –108 dBm
Modulation type 2-GFSK
Communication speed 50 kbps
Transmission frequency 868,1 MHz
Number of channels 1
DI - Parameters of binary inputs DC (group A)
Parameters valid for inputs on the terminals AI/DI1, AI/DI2
Number of inputs in group 2
Common wire minus
Combined input type DI/AI Active, for sensing potential-free contacts and measuring resistance sensors
Galvanic separation of inputs from internal circuits No
Diagnostics signaling of excited input in Mosaic
Max. measuring voltage on the connected contact 3,3 V DC
Internal input resistance 4,7 kΩ
RO - Parameters of binary relay outputs (group A)
Parameters valid for the terminals DO1, COM
Number of relay outputs 1
Output type electromechanical relay, unprotected output
Contact type NO - Normally Open
Switching voltage 250 V AC max., 5 V AC min., 30V DC max.
Switching current 12 A max., 100 mA min.
Switching power 250 W (with current measuring), 2760 W (without current measuring), see connection diagrams
Short-circuit protection No
Short-term output overload - inrush max. 800 A (max. 200 μs)
Contact opening time typ. 4 ms
Limit values of switched resistive load max. 3A at 30 V DC or 230 V AC
Switching inductive load limits DC13 max. 3 A at 30 V DC
Switching inductive load limits AC15 max. 3 A at 230 V AC
Switching frequency without load max. 300 switching / min.
Mechanical life min. 5,000,000 cycles
Electrical life at maximum resistive load min. 100,000 cycles
Electrical life at maximum load inductive DC13 min. 100,000 cycles
Electrical life at maximum load inductive AC15 min. 100,000 cycles
Treatment of inductive load External RC element, varistor (AC), diode (DC)
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals AI/DI1, AI/DI2, N
Voltage 0-3,3 V
Passive sensor Resistance transmitter 0-15 kOhm
Passive sensor NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
DI: Voltage-free contact 0 when> 1.5 kOhm, 1 when <0.5 kOhm
Power supply
Nominal supply voltage (V) 230 V AC
Typical power input 3 W
Maximum power input 4,5 W
Maximum current consumption (mA) < 20 mA
Galvanic separation of power supply from internal circuits No
Internal protection No
Size and weight
Weight approx. 50 g
Product dimensions (width x height x depth) 35 x 92 x 40 mm
Module width 35 mm
Module height 92 mm
Module depth 40 mm
Operating conditions, product standards
Product standard ČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units
Protection class of electrical object II, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) IP20
Operating areas Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation I, according to ČSN EN 60664-1 ed_2:2008 (idt IEC 60641-1:2007)
Type of device Module on DIN rail
Working position Any
Type of operation (operating frequency) Continuous
Ambient temperature operating range -20 °C to + 55 °C
Operating temperature maximum (° C) +55°C
Operating temperature minimum (° C) -20°C
Storage temperature range –25 °C to +70 °C
Relative humidity from 10 % up to 95 % without condensation
Atmospheric pressure min. 70 kPa (<3,000 m above sea level)
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission A, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015)
Electromagnetic compatibility / Immunity min. as required by EN 61131-2: 2007
Sinusoidal vibration endurance 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Installation
Description Mounting in a cabinet or luminaire
Attention! The device may contain parts with dangerous voltages, covers being removed, or cabling manipulated, or disconnect the appropriate circuits or turn off the power !.
Connection
Power connection terminal block with spring terminal 1.5 mm2, push-in
Connection of inputs / outputs terminal block with spring terminal 1.5 mm2, push-in
Wireless network - antenna Wireless network - antenna SMA connector (male)
Module operation
Module configuration The module is operated, set up and diagnosed from the Mosaic development environment.
Commissioning The module is operated in the RFox2 radio network as a peripheral module, the settings are made in the Mosaic programming environment project manager, see the TXV 003 93 manual with the description of RFox2Lib.
Module diagnostics The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Instructions Because the module contains semiconductor components, it is necessary to follow the principles for working with components sensitive to electrostatic charges during handling. Repairs are performed exclusively by the manufacturer's service center or the manufacturer's authorized service.
Warranty
Generally Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.

HW documentation

PDF

R-SL-0201L-A Basic Documentation

1.26 MB, (EN)
  • Example of DLC-Prog 70W driver control by R-SL-0201L-A VO lamp module - The connection example shows the ballast control for the LED source by the R-SL-0201L-A  module. The ballast used in the example is Layrton DLC-prog 70W . It is a programmable very universal ballast, which allows control of the brightness o...
  • Example of GPF-60D-1400 driver control by R-SL-0201L-A VO lamp module - Fig. 1 shows an example of connection of the R-SL-0201L-A module for brightness control of the GPF-60D-1400 LED driver, eg for installation in a VO lamp.   Fig. 1 example of lamp driver control by a R-SL-0201L-A  module No...
  • R-SL-0201L-A - R-SL-0201L is a peripheral module designed, for example, for remote control of a street lamp in the RF network of the RFox2 system. The module contains 1x relay output for switching the lamp power supply, PWM output for brightness control, intern...
  • Smart City - modules for controlled control of ballasts for public lighting - ...dnoho až dvou předřadníků pro použití v lampách veřejného osvětlení. C-DM-0002L-10V is two-channel on CIB buses, The R-SL-0201L-A is single-channel connected to the Foxtrot control panel wirelessly at a frequency of 868MHz. It has two inputs...

No data available.