English
C-IT-0504STXN 133 26
C-IT-0504S; CIB, 5x AI/DI - RTD or contact, 4x AO (0-10V/10mA)
| DI | 5x DI/AI see AI |
|---|---|
| DO | |
| AI | 5x DI/AI see DI |
| AO | 4x AO |
| COM | 1x CIB slave |
| SENSOR |
| Picture | Variant | Variant description |
|---|---|---|
|
C-IT-0504S |
The C-IT-0504S module (order no .: TXN 133 26) is intended for the connection of analog or binary signals and 0 - 10 V analog outputs directly to the CIB wiring bus. Inputs, outputs and buses are connected to the module via pen terminals. Universal inputs can be set to binary or analog program in two groups. The first group contains 4 inputs, the second 1 input. The settings are then common to the whole group.
For example, one temperature sensor and four input-contacts or one input-contact and four temperature sensors. Resistance sensors PT1000 or Ni1000 or a sensor with a thermistor NTC12k or KTY81-121 against a common GND conductor are used for temperature measurement. The resistance is converted in the module to a numerical temperature value and transmitted to the central unit via the CIB bus. For another type of resistance sensor, a resistance measurement range of 0 to 160 kΩ can be selected, but the conversion to temperature and linearization must be performed only at the level of the user program. The module software - firmware - is optimized to increase the accuracy and linearize the measuring range of the sensor in the module.
Binary signals are connected to the inputs only as free, without voltage contact against the common conductor GND. The binary input can also operate in balanced input mode. The voltage of the analog outputs 0 - 10 V is output on the conductor against the common GND conductor.
For example, one temperature sensor and four input-contacts or one input-contact and four temperature sensors. Resistance sensors PT1000 or Ni1000 or a sensor with a thermistor NTC12k or KTY81-121 against a common GND conductor are used for temperature measurement. The resistance is converted in the module to a numerical temperature value and transmitted to the central unit via the CIB bus. For another type of resistance sensor, a resistance measurement range of 0 to 160 kΩ can be selected, but the conversion to temperature and linearization must be performed only at the level of the user program. The module software - firmware - is optimized to increase the accuracy and linearize the measuring range of the sensor in the module.
Binary signals are connected to the inputs only as free, without voltage contact against the common conductor GND. The binary input can also operate in balanced input mode. The voltage of the analog outputs 0 - 10 V is output on the conductor against the common GND conductor.
| Order num. | TXN 133 26 |
|---|---|
| Teco code | TXN 133 26 |
| Categories | CFox - Built-in modules |
| Tags | - |
| COM - System buses | |
|---|---|
| CIB - Common Installation Bus (R): Installation I/O bus | 1x CIB slave |
| DI - Organization of binary inputs | |
| Total number of binary inputs | 5 |
| Number of groups of binary inputs | 1 |
| Organization of binary inputs into groups | 5x DI (DI/AI1 - DI/AI5) |
| DI - Parameters of binary inputs DC (group A) | |
| Parameters valid for inputs on the terminals | DI/AI1 - DI/AI5 |
| Common wire | GND - module ground |
| Combined input type | DI/AI Active, for sensing potential-free contacts and measuring resistance sensors |
| Galvanic isolation of inputs from internal/peripheral circuits | No |
| Max. measuring voltage on the connected contact | 3,3 V DC |
| Internal input resistance | 2,2 kΩ |
| Max. resistance for closed contact, log. 1 | < 0,5 kΩ |
| Min. resistance for open contact, log. 0 | > 1,5 kΩ |
| Balanced resistance input | 2× 1k1 (tamper/0/1/tamper) |
| AI - Analog Input Ranges (Group A) | |
| Passive sensor | Pt1000, W100 = 1,385 (-90 to +400 ° C) |
| Passive sensor | Pt1000, W100 = 1,391 (-90 to +400 ° C) |
| Passive sensor | Ni1000, W100 = 1,500 (–60 to +200 ° C) |
| Passive sensor | Ni1000, W100 = 1.617 (-60 to +200 ° C) |
| Passive sensor | Resistance transmitter 0-160 kOhm |
| Passive sensor | KTY81-121; PTC thermistor (-55 to + 125 °C) |
| Passive sensor | NTC Thermistor 12k / 25 °C (-40 to + 125 °C) |
| DI: Balanced resistance input | Yes |
| Input impedance in signal range RTD | > 2,2 kΩ |
| Resistance measurement error - maximum error at 25 ° C | ± 0.5% of full scale |
| AO - Analog output parameters | |
| The number of groups of analogue outputs | 1 |
| Number of outputs in group | 4 |
| Number of outputs and their organization into groups | 4x AO (AO1-AO4) |
| Common wire of group | GND terminal |
| Galvanic isolation from internal circuits | No |
| Output type | active voltage output |
| Voltage output - voltage | 0 - 10 V |
| Voltage output - Resolution 1 LSB | 10,546 mV |
| Voltage output - Adjustable range | 0 ÷ 130 % Ujm |
| Voltage output - Load resistance | >1 kΩ |
| Voltage output - Load capacity | 250 nF |
| Power supply | |
| Supply voltage, tolerances | 24/27 V DC from CIB bus |
| Typical power input | 1 W |
| Maximum power input | 2,5 W |
| Module thermal/power loss | 1 W |
| Power supply from CIB - typical current consumption (mA) | 20 mA |
| Power supply from CIB - maximum current consumption (mA) | 80 mA |
| Description of power supply | The difference between the typical and the maximum power is given by the possible load on the CIB buses |
| Size and weight | |
| Weight approx. | 7 g |
| Product dimensions (width x height x depth) | 55 × 26 × 20 mm |
| Operating conditions, product standards | |
| Product standard | ČSN EN 60730-1 ed.4 :2017 (EN 60730-1:2016) -Automatic electronic control device (for household and similar purposes) |
| Protection class of electrical object | III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016) |
| IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) | IP10B |
| Operating areas | Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005) |
| Degree of pollution | 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007) |
| Overvoltage category installation | II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007) |
| Type of device | In the installation box, under the cover |
| Working position | Any |
| Type of operation (operating frequency) | Continuous |
| Ambient operating temperatures | 0 ° C to + 70 ° C |
| Operating relative humidity | from 10 % up to 95 % without condensation |
| Operating atmospheric pressure | min. 70 kPa (<3,000 m above sea level) |
| Storage temperatures | –25 ° C to + 85 ° C |
| Electromagnetic compatibility, Mechanical endurance | |
| Electromagnetic compatibility / Emission | ČSN EN 55022 ed2:2007 (mod CISPR22:2005) |
| Electromagnetic compatibility / Immunity | min. according to ČSN EN 60730-1 ed.2: 2001 |
| Sinusoidal vibration endurance | 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.) |
| Packaginng, transportation, storage | |
| Description | Модуль упакован в антистатический пакет. Эта документация также является частью пакета. Внешняя упаковка осуществляется в соответствии с объемом заказа и способом транспортировки в транспортной упаковке, снабженной этикетками и другими данными, необходимыми для транспортировки. Продукт не должен подвергаться воздействию прямых погодных условий во время транспортировки и хранения. Соложение продукта разрешено только в чистых помещениях. без токопроводящей пыли, агрессивных газов и паров. Наиболее подходящая температура хранения - 20 ° C. |
| Connection | |
| Connection description | An example of module connection is shown in the following figure. |
| Connection of power and system communication | terminal block with spring terminal 0.15-0.5 mm2, push-in |
| Connection of inputs / outputs | terminal block with spring clamp 0.15-0.5 mm2, push-in |
| Module operation | |
| Module configuration | The module is operated, set up and diagnosed from the Mosaic development environment. |
| Commissioning | The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module. |
| Module diagnostics | The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment. |
| Maintenance | |
| Description | The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected. |
| Notice | Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!! |
| Warranty | |
| Generally | Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s. |
| Notice | You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change. |
HW documentation
C-IT-0504S - Basic documentation
813.75 kB, (EN)
User manuals
Peripheral modules on the CIB Common Installation Bus(R) (en), TXV00413_02
13.94 MB, (EN, RU, DE, UA)
Files for designers
Foxtrot 2 - element library for SchemataCAD, v. 2024/01
6.79 MB
Foxtrot 2 - library of elements in DXF and DWG formats, v. 2024/01.
20.49 MB
EC - Declaration of Conformity
Foxtrot - EC Declaration of conformity
295.20 kB, (EN, RU, DE, UA)
- C-IT-0504S - The C-IT-0504S module (order number.: TXN 133 26) is designed to connect analogue or digital signals and analogue outputs 0 - 10 V directly on the CIB bus. The inputs, outputs and the CIB bus should be connected to the module via a fixed terminal bl...
- The GIRA 2001 xx controller scanned by the C-IT-0504S input module - ...tons (with a 24 VAC/DC nominal power supply) and two LEDs (24 VDC, 1mA power supply). It can be connected to the embedded C-IT-0504S module, which should be placed in the flush-box under the controller, and the result is a complete controller o...
- Wall push-buttons scanned by the input module C-IT-0504S - The built-in C-IT-0504S module can be used in a similar way as the C-IT-0200S ; it can scan e.g. 4 push-buttons of the controller, measure the interior temperature, and it can also control up to 4 LEDs, if the controller is equipped with...
- The short-stroke push-buttons S-WS-0004R-Merten, connection to the C-IT-0504S - ...tputs and measuring the temperature (the NTC 12k sensor is fitted under the fingerboard of the module); e.g. the CFox module C-IT-0504S may be used. The S-WS-0400R-Merten can also be connected to different inputs and outputs while maintaining the...
- A miniature terminal block - The miniature terminals used by some built-in modules, such as the C-IT-0504S , and some other peripheral modules, e.g. the S-WS-0400R-Merten , are screwless (spring) fixed terminals with a 2.5mm spacing. The wire can be removed from the term...
- Control push-buttons on the wall (control of lighting, blinds, etc.) - Control units on the wall (a replacement of conventional switches) can be designed or integrated into the system in several ways, depending on the comfort, options, price and assortment. The first one is a controller as the bus element of...
No data available.