English
C-RI-0401STXN 133 47
C-RI-0401S; CIB, 2x AI/DI RTD or contact; 1x IR transmitter, 1x IR receiver, 1x AI - light intensity (including IR LED+IR Sensor)
| DI | 2x AI/DI |
|---|---|
| DO | |
| AI | |
| AO | |
| COM | 1x CIB slave |
| SENSOR |
| Picture | Variant | Variant description |
|---|---|---|
|
C-RI-0401S |
C-RI-0401S is a module on the CIB Common Installation Bus®, which contains 2 analog / binary inputs, 1 input for the light sensor, 1 input for the IR receiver demodulator and 1 output for the IR transmitter.
| Order num. | TXN 133 47 |
|---|---|
| Teco code | TXN 133 47 |
| Categories | CFox - Built-in modules |
| Tags | - |
| COM - System buses | |
|---|---|
| CIB - Common Installation Bus (R): Installation I/O bus | 1x CIB slave |
| DI - Parameters of binary inputs DC (group A) | |
| Parameters valid for inputs on the terminals | AI1/DI1, AI/DI2 |
| Number of inputs in group | 2 |
| Common wire | GND - module ground |
| Combined input type | DI/AI Active, for sensing potential-free contacts and measuring resistance sensors |
| Galvanic isolation of inputs from internal/peripheral circuits | No |
| Diagnostics | signaling of excited input in Mosaic |
| Input voltage | 3.3 V from internal source |
| Input current at log. 1 (typ.) | 3,3 mA |
| Delay from log. 0 to log. 1 | 10 ms |
| Delay from log. 1 to log. 0 | 300 ms |
| The minimum width of the captured pulse | 10 ms |
| AI - Organization of analog inputs | |
| Total number of analog inputs | 2 |
| Common wire | Plus |
| Galvanic separation from internal circuits | No |
| External power supply | No |
| Digital resolution | 12 bit |
| Converter type | Approximation |
| conversion time | 500 μs |
| AI - Analog Input Ranges (Group A) | |
| Parameters valid for inputs on the terminals | AI1/DI1, AI/DI2 |
| Passive sensor | Pt1000, W100 = 1,385 (-90 to +400 ° C) |
| Passive sensor | Pt1000, W100 = 1,391 (-90 to +400 ° C) |
| Passive sensor | Ni1000, W100 = 1,500 (–60 to +200 ° C) |
| Passive sensor | Ni1000, W100 = 1.617 (-60 to +200 ° C) |
| Passive sensor | Resistance transmitter 0-160 kOhm |
| Passive sensor | KTY81-121; PTC thermistor (-55 to + 125 °C) |
| Passive sensor | NTC Thermistor 12k / 25 °C (-40 to + 125 °C) |
| Input impedance in signal range RTD | > 1 kΩ |
| Resistance measurement error - maximum error at 25 ° C | ± 2% of full scale |
| Resistance measurement error - temperature coefficient | ± 0,1% of full scale |
| Resistance measurement error - non-linearity | ± 0.2% of full scale |
| Resistance measurement error - repeatability at steady conditions | 0.5% of full scale |
| Detection of disconnected sensor | No |
| Input parameters for connecting a light sensor | |
| Number of inputs | 1 |
| Galvanic isolation | No |
| Lighting - Sensor type | Photodiode BPW21 |
| Lighting - Conversion time | 500 μs |
| Lighting - Measuring range | 0 lx ÷ 50000 lx |
| Lighting - Measurement error | <5% of range |
| Lighting - Temperature coefficient | ± 0.1% of full scale / ° C |
| Lighting - Linearity of measurements | ± 0.2% of full scale |
| Lighting - Repeatability under steady state conditions | 0.5% of full scale |
| Parameters of IR receiver / transmitter inputs / outputs | |
| Number of inputs for connecting the IR receiver demodulator | 1 |
| Demodulator power supply | 3,3 V |
| Galvanic separation from internal circuits | No |
| Demodulator carrier frequency | 36 kHz |
| Output parameters for IR transmitter connection | |
| Number of outputs | 1 |
| Transmitter power supply | 3,3 V |
| Short circuit protection | No |
| Galvanic separation from internal circuits | No |
| IR transmitter | IR LED (IFMAX = 100mA) + resistor according to IF |
| IR transmitter, example | IR LED UF = 1.2V, IF = 20mA → R = 100Ω |
| Power supply | |
| Supply voltage, tolerances | 24/27 V DC from CIB bus |
| Maximum power input | < 0,5 W |
| Power supply from CIB - maximum current consumption (mA) | 25 mA |
| Power supply from CIB - internal protection | No |
| Size and weight | |
| Weight approx. | 7 g |
| Product dimensions (width x height x depth) | 55 x 32 x 13 mm |
| Operating conditions, product standards | |
| Product standard | ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999) |
| Protection class of electrical object | I, according to ČSN EN 61140: 2003 (idt IEC 61140: 2001) |
| IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) | IP10B |
| Operating areas | Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005) |
| Degree of pollution | 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007) |
| Overvoltage category installation | II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007) |
| Type of device | In the installation box, under the cover |
| Working position | Any |
| Type of operation (operating frequency) | Continuous |
| Ambient operating temperatures | -10 °C to + 55 °C |
| Operating relative humidity | from 10 % up to 95 % without condensation |
| Operating atmospheric pressure | min. 70 kPa (<3,000 m above sea level) |
| Storage temperatures | –25 °C to +70 °C |
| Electromagnetic compatibility, Mechanical endurance | |
| Electromagnetic compatibility / Emission | B, according to EN 55022: 1999 (mod CISPR22: 1997) |
| Electromagnetic compatibility / Immunity | min. according to ČSN EN 60730-1 ed.2: 2001 |
| Sinusoidal vibration endurance | 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.) |
| Packaginng, transportation, storage | |
| Description | Модуль упакован в антистатический пакет. Эта документация также является частью пакета. Внешняя упаковка осуществляется в соответствии с объемом заказа и способом транспортировки в транспортной упаковке, снабженной этикетками и другими данными, необходимыми для транспортировки. Продукт не должен подвергаться воздействию прямых погодных условий во время транспортировки и хранения. Соложение продукта разрешено только в чистых помещениях. без токопроводящей пыли, агрессивных газов и паров. Наиболее подходящая температура хранения - 20 ° C. |
| Installation | |
| Assembly description | The C-RI-0401S module can be mounted in any position in the installation box or under the device cover. Installation of the assembly (basic module and possibly peripheral modules) is performed according to TXV 004 13. |
| Connection | |
| Connection of power and system communication | Ribbon flat conductors 0.15 / 0.5 mm2 |
| Module connection |
The combined module is implemented as a CIB bus module, which provides communication. The power supply of the module is from an external source. The CIB bus can have any topology and branching up to a distance of 500 m and up to 32 units on one CIB branch. The CIB bus master is the FOXTROT basic unit or module, for example MI2-02M. Further information can be found in the manual Peripheral modules on the CIB TXV 004 13. An example of module connection is shown in the following figure. |
| Module operation | |
| Commissioning | The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module. |
| Maintenance | |
| Description | The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected. |
| Notice | Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!! |
| Warranty | |
| Generally | Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s. |
| Notice | You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change. |
HW documentation
C-RI-0401S - Basic documentation
697.15 kB, (EN)
User manuals
Peripheral modules on the CIB Common Installation Bus(R) (en), TXV00413_02
13.94 MB, (EN, RU, DE, UA)
Files for designers
Foxtrot 2 - library of elements in DXF and DWG formats, v. 2024/01.
20.49 MB
Foxtrot 2 - element library for SchemataCAD, v. 2024/01
6.79 MB
EC - Declaration of Conformity
Foxtrot - EC Declaration of conformity
295.20 kB, (EN, RU, DE, UA)
- C-RI-0401S - The C-RI-0401S (order no TXN 133 47) is a combined module designed for a connection on the CIB bus. The module contains 2 universal analogue/binary inputs; it is possible to connect either passive resistive temperature sensors to them, or they can b...
- C-RI-0401R - ...hes, sockets, etc.), the C-RI-0401R consists of two parts: The first part - the actual module (it corresponds with the C-RI-0401S module) - is placed in the flush box, which enables the connection to the CIB bus and provides processing of all c...
- Measuring outdoor lighting, the sensor is installed by the customer - The outdoor lighting is measured by the C-RI-0401S module, whose built-in version is placed in the flush box; it is terminated with a connector, to which the BPW21 lighting sensor itself should be connected (it has to be ordered separately)....
- Measuring the intensity of outdoor lighting - ...the lighting sensor, the module also includes a terminated outdoor temperature sensor. Inside the box is located the C-RI-0401S module, whose detailed description is given at the end of this manual, where the module C-RI-0401S is des...
- Measuring the interior lighting - ...d by the C-RI-0401R-design module, which consists of two parts: The first, recessed part (corresponding to the C-RI-0401S ), is placed in the flush box, typically under the second wall-mounted design part. The second wall-mounted...
- Measuring the lighting - ...cent spaces in the flat is 1:5. The level of outdoor lighting and indoor illumination is measured by the C-RI-0401S module, or its variants, e.g. the C-RI-0401R-design, or the C-RI-0401I....
- An IR transmitter and receiver to be mounted on the wall: the C-RI-0401R-design - ...le that goes through it to the second part of the module - the part with the bus (it is available separately, such as the C-RI-0401S ). The module is available in several designs; those based on the customer's special requirements are on...
- Infrared (IR) control - ...des (IR transmission). It consists of the internal part (the electronics, the CIB connection) available separately as the C-RI-0401S , and the design part, which is implemented in accordance with the required design with a wall-mounted module wi...
No data available.