R-IS-0203M-A, control of 3 external SSRTXN 142 18.A

R-IS-0203M-A; RFox2, 2x AI / DI, 3x AO / PWM- for control of external SSR, 3f, radio type A

DO 3x DO (PWM)
AI 2x AI
AO 1x AO
COM 1x RFox2 slave
Picture Variant Variant description
R-IS-0203M-A, control of 3 external SSR
R-IS-0203M-A; RFox2, 2x AI / DI, 3x AO / PWM- for control of external SSR, 3f, radio type A
Order num. TXN 142 18.A
Teco code TXN 142 18.A
Categories RFox2 - DIN Rail Modules
Tags -
COM - Wireless network
RFox2 wireless network RFox2 Slave
Communication frequency band 868,1 MHz
Transmission power +14 dBm
Input sensitivity –108 dBm
Modulation type 2-GFSK
Communication speed 50 kbps
DO - Parameters of binary transistor outputs (group A)
Parameters valid for the terminals GND, PWM1, PWM2, PWM3 (C1, C2, C3, C4)
Number of transistor outputs 3
Number of output groups 1
Number of outputs in group 3
Common group conductor minus
Output type MOSFET (High-side switch)
Switching current, output load 20 mA max.
Special functions (A) PWM
Operating frequency 1 Hz - 1 kHz
Alternation settings 0 – 100 %
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals AI1, AI2, GND (B3, B2, B1)
Passive sensor Pt1000, W100 = 1,391 (-90 to +400 ° C)
Resistance measurement error - temperature coefficient 3850 ppm / °C
AO - Analog output parameters
Number of outputs in group 1
Parameters valid for the terminals AO (B4), GND (B1)
Common wire of group GND terminal
Output type active voltage output
Voltage output - voltage 0 - 10 V
Voltage output - maximum output current 10 mA
Power supply
Supply voltage, tolerances 90 – 270 V AC
Input voltage frequency 50-60 Hz
Maximum power input 2,5 W
Galvanic separation of power supply from internal circuits No
Insulation voltage of galvanic separation 3 000 VDC
Internal protection Yes, non-refundable
Size and weight
Weight approx. 75 g
Module width in multiples of M (17.5 mm) 1,5M
Product dimensions (width x height x depth) 23 x 95 x 58 mm
Operating conditions, product standards
Product standard ČSN EN 60730-1 ed.4 :2017 (EN 60730-1:2016) -Automatic electronic control device (for household and similar purposes)
Protection class of electrical object II, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) IP20
Operating areas Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device Module on DIN rail
Working position Vertical
Type of operation (operating frequency) Continuous
Ambient operating temperatures 0 ° C to + 55 ° C
Operating relative humidity from 10 % up to 95 % without condensation
Operating atmospheric pressure min. 70 kPa (<3,000 m above sea level)
Storage temperatures –25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission B, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015)
Electromagnetic compatibility / Immunity min. according to ČSN EN 60730-1 ed.3: 2012
Sinusoidal vibration endurance 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Connection description An example of module connection is shown in the following figure. Any type designed for the 868 MHz band with an SMA connector (pin) can be used as an antenna.
Warnings / Cautions CAUTION: The device contains parts with dangerous voltage, disconnect the relevant circuits or switch off the power supply before removing the covers or handling the wiring!
Connection of power and system communication terminal block with screw terminal 2.5 mm2
Connection of inputs / outputs terminal block with screw terminal 2.5 mm2
Module operation
Commissioning The module is operated in the RFox2 radio network as a peripheral module, the settings are made in the Mosaic programming environment project manager, see the TXV 003 93 manual with the description of RFox2Lib.
Module diagnostics The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Description The module does not require any maintenance under general installation conditions.
Instructions Because the module contains semiconductor components, it is necessary to follow the principles for working with components sensitive to electrostatic charge during repairs. Repairs are performed exclusively by the manufacturer's service center or the manufacturer's authorized service.
Generally Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.

HW documentation


R-IS-0302-A - Basic documentation

146.34 kB

Files for designers


Foxtrot 2 - library of elements in DXF and DWG formats, v. 2024/01.

20.49 MB

Foxtrot 2 - element library for SchemataCAD, v. 2024/01

6.79 MB

No data available.

No data available.