CP-2000.11NDNNTXN 120 00.11NDNN

CP-2000, CPU/1core, 2xETH100/10,---, 128kB databox, LCD 20mm, 1x RS232, CH1-4, 4xAI/DI, 3xDI/230VAC, 2xRO, 2xCIB

3x DI (230 V AC)
DO 2x RO
AI 4x DI/AI, see DI
COM 2x ETH 10/100
1x RS-232
4x Serial channel (2x free slot)
1x USB device
1x USB host
1x TCL2 master
2x CIB master
Picture Variant Variant description
CP-2000.11NDNN Databox: 128 kB
Processor: 1 core, ARMv7 792 MHz
Display: OLED display large 55 x 13 mm
CP-2000.11NDLN Databox: 128 kB
Processor: 1 core, ARMv7 792 MHz
Display: OLED display large 55 x 13 mm
Modem: LTE1 installed
CP-2000 is a basic module of the second generation, which is mainly equipped with:
  •     Two CIB Common Installation Bus® masters with full power supply so that up to 64 sensor and actuator modules for this two-wire bus can be connected directly
  •     Additional CIB branches are added by new generation external masters connected via LAN (ethernet).
  •     TCL2 system expansion bus master.

It is equipped with a total of 9 I / Os:
  •     four multipurpose inputs, each of which can be used either as analog or as binary
  •     one input for monitoring the presence of the 230 V AC mains supply
  •     two binary inputs at voltage level 230V AC for HDO monitoring (mass remote control)
  •     two separate relay outputs.

Communication capabilities of the basic module CP-2000:
  •     2x Ethernet interface 100 Mbit / s, each with up to 32 simultaneous connections (programming and general IP communication)
  •     USB micro (programming)
  •     USB A for Flash memory, WiFi adapter (client and AP - Access point) etc.
  •     Variant with built-in LTE modem for direct wireless connection to the Internet via a mobile network operator
  •     Slots for up to 4 optional serial interfaces RS-485, RS-232

24 V DC power supply, possibility of direct connection of a backup battery for uninterrupted operation in case of 230 V AC mains failures.

CP-2000 is equipped with a new powerful central unit (CPU series L) with memory
  •     1 MB for user program,
  •     128 MB internal disk for storing files with parallel access from the LAN as a network disk,
  •     16MB fast RAM disk
  •     microSD card slot up to 1 TB
  •     File management is provided by a journaling file system
  •     Local communication with the user via OLED display (4 lines / graphic) and 6-key keyboard
Order num. TXN 120 00.11NDNN
Teco code TXN 120 00.11NDNN
Categories Foxtrot 2 - Basic modules
Tags -
System parameters of the central unit
Row of central unit I
User program memory 1 MB
Memory for user variables / including RETAIN variables 320 kB/48 kB
Instruction length 4 Byte
Backup of program source code in PLC Yes, optional in Mosaic
On-line program change in PLC Yes, including I / O configuration change
DataBox - additional internal data memory 128/257 kB, optional
File system - Internal Drive in PLC 128 MB, journaling file system
File system - RAM disk PLC 16 MB
File System - USB Flash Drive Supported
File system - Micro SD card supported (except for variants with WLAN1)
Optional memory card slot microSD - Card Slot (<= 1TB)
Cycle time per 1k of logic instructions 0,036 ms
Cycle time for 1k integer operations 0,044 ms
Cycle time for 1k floating point operations 0,043 ms
Development environment Mosaic v2018.2 or higher
Programming languages ST, IL, LD, FBD, SFC, CFC
RTC - Real time circuit No
RTC - Backup time typ. 500 hours
Integrated Web server Yes
Integrated Datalogger Yes
Access to PLC variables via web API Yes
COM - Communication - IP/Ethernet
Ethernet 10/100 Mb (ETHx) 2
WLAN1 (internal, optional) 1
WLAN2 (external via USB host, optional) 1
LTE interface (LTEx, optional) 1
Available system modes on ETH and WLAN UNI, PC, PLC, PLD
Available system modes on LTE UNI - Exchange over UDP, TCP and support SSL / TLS encryption PC - EPSNET UDP / EPSNET TCP
TCP / IP protocol Yes
UDP protocol Yes
HTTPS protocol Yes
HTTP protocol Yes
WebSocket protocol Yes
Protocol MODBUS/TCP Yes
SMTP protocol Yes
IEC 60870-5-104 protocol Yes
USB devices interface 1x micro-USB
USB host interface 1x USB-A
Available system modes on USB PC
COM - System buses
TCL2 - system I/O bus 1x TCL2 master
TCL2 - Range of one branch of the system I/O bus 10 I / O modules + 4 operator panels + 6 serial channels
CIB - Common Installation Bus (R): Installation I/O bus 2x CIB master (2x 1 A)
CIB - Address range of one branch of the installation bus 32 CFox I/O modules
DI - Parameters of binary inputs DC (group A)
Parameters valid for inputs on the terminals AI0/DI0 - AI3/DI3
Number of inputs in group 4
Common wire AGND - module ground
Combined input type DI/AI Active, for sensing potential-free contacts and measuring resistance sensors
Galvanic isolation of inputs from internal/peripheral circuits No
Input voltage for log. 1 1 V DC max.
Input current at log. 1 (typ.) -1,7 mA
The minimum width of the captured pulse 1 ms
Notice Note that the GND terminals in the 24 V DC and ANALOG OUTPUTS arrays they are connected inside the system. It is not desirable to connect the GND terminal in the ANALOG field OUTPUTS with a negative pole power supply system also inputs as it would cross the other the GND terminal has closed the loop and thereby potentially induced interfering signals.
DI - Parameters of binary AC inputs
Parameters valid for AC inputs on the terminals IN230V, HDO0, HDO1
Total number of binary AC inputs 3
Number of groups of AC inputs 2
Organization of binary inputs into groups 1x (IN230V), 2x (HDO1, HDO2)
Common wire L
Input type 230 V AC
Galvanic isolation of internal circuits Yes
Input voltage for log. 1 230 V AC typ., 200 V AC min., 250 V AC max.
Input current at log. 1 (typ.) 5 mA typ.
RO - Parameters of binary relay outputs (group A)
Parameters valid for the terminals DO0–DO5, DO7–DO10
Number of relay outputs 2
Organization of relay outputs into groups 1x (DO0) +1x (DO2)
Output type electromechanical relay, unprotected output
Contact type NO - Normally Open
Galvanic separation from internal circuits Yes
Galvanic isolation between groups Yes
Switching current 16 A max. NO/10 A max NC, 100 mA min.
Switching voltage 250 V AC max., 5 V AC min., 30V DC max.
Short-term output overload - inrush 80 A max. (20 ms max.)
Contact closing time typ. 15 ms
Contact opening time typ. 5ms
Limit values of switched resistive load max. 16A at 30 V DC or 230 V AC
Mechanical life min. 20 000 000 cycles
Electrical life at maximum resistive load min. 100,000 cycles
Short-circuit protection No
Treatment of inductive load External RC element, varistor (AC), diode (DC)
Insulation voltage between outputs and internal circuits 3750 V AC
Isolation voltage between groups of outputs to each other 3750 V AC
AI - Organization of analog inputs
Total number of analog inputs 4
Number of analog input groups 1
Organization of analog inputs into groups 4x (AI0/DI0-AI3/DI3)
Input type With common clamp
Common wire Minus
Galvanic separation from internal circuits No
External power supply No
Digital resolution 12 bit
Converter type Approximation
conversion time 20 μs
Operating modes periodic input sensing
Insulation potential 500 V DC between input and internal circuits
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals AI0/DI0 - AI3/DI3
Passive sensor Pt1000, W100 = 1,385 (-90 to +400 ° C)
Passive sensor Pt1000, W100 = 1,391 (-90 to +400 ° C)
Passive sensor Ni1000, W100 = 1,500 (–60 to +200 ° C)
Passive sensor Ni1000, W100 = 1.617 (-60 to +200 ° C)
Passive sensor Resistance transmitter 0-2 kOhm
Passive sensor Resistance transmitter 0-200 kOhm
Passive sensor KTY81-121; PTC thermistor (-55 to + 125 °C)
Passive sensor NTC Thermistor 5k / 25 °C (–40 to + 125 °C)
Passive sensor NTC Thermistor 10k / 25 °C (-40 to + 125 °C)
Passive sensor NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
Passive sensor NTC Thermistor 15k / 25 °C (-40 to + 125 °C)
Passive sensor NTC Thermistor 20k / 25 °C (-40 to + 125 °C)
DI: Voltage-free contact 0 when> 1.5 kOhm, 1 when <0.5 kOhm
Input impedance in signal range RTD > 4 kΩ
Resistance measurement error - maximum error at 25 ° C ± 0.5% of full scale
Detection of disconnected sensor yes, in status word, range overflow
Power supply
Supply voltage, tolerances 24 V DC, +25%, -15%, SELV
Supply voltage when backing up with an external battery 27 V DC, +10%, –15%, SELV
Maximum power input 75 W
Internal protection Yes, PTC reversible fuse
CIB branch power supply - parameters of the built-in master 2x 1 A/ 24-27 V DC
Power supply from ETH, passive PoE - input (appliance) ETH1/Power In
Power supply from ETH, passive PoE - output (source) ETH2 / Power out, jumper configuration
Power supply from ETH, passive PoE - injector parameters 24 V DC, 1A
Possibility of backing up the power supply of the basic module and CIB Yes, by battery 2x 12 V DC, 1x 24 V DC
Battery parameters 24 V (2x 12V), max. 18 Ah
Size and weight
Weight approx. 300 g
Product dimensions (width x height x depth) 158 x 90 x 62 mm
Module width in multiples of M (17.5 mm) 9M
Operating conditions, product standards
Product standard ČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units
Protection class of electrical object II, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) IP20
Operating areas Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device Module on DIN rail
Working position Vertical
Type of operation (operating frequency) Continuous
Ambient operating temperatures -20 °C to + 55 °C
Operating temperature maximum (° C) +55°C
Operating temperature minimum (° C) -20°C
Operating relative humidity from 10 % up to 95 % without condensation
Operating atmospheric pressure min. 70 kPa (<3,000 m above sea level)
Storage temperatures –25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission B, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015)
Emmisions - note In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action.
Electromagnetic compatibility / Immunity min. as required by EN 61131-2: 2007
Sinusoidal vibration endurance 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description The module is packed in a paper box according to the internal packing instructions. The package includes the following documentation. The outer packaging is carried out according to the scope of the order and the method of transport to the transport a package bearing the transport labels and other particulars necessary for transport. Transport from the manufacturer is carried out in the manner agreed upon when ordering. Product transport the customer's own means must be carried out by covered means of transport, in the specified position label on the packaging. The box must be stowed so as to prevent spontaneous movement a damage to the outer packaging. The product must not be exposed to direct weathering during transport and storage influences. Transport is allowed at temperatures from -25 ° C to +70 ° C, relative humidity 10% up to 95% (non-condensing) and a minimum atmospheric pressure of more than 70 kPa. Storage of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Assembly description Switchboard mounting
Assembly description The basic module is mounted vertically on the U-rail ČSN EN 50022. The installation of the assembly (basic module and peripheral modules, if applicable) is performed according to TXV 004 50.
Exchangeable submodules The optional MR-013x submodules of the serial interface are mounted in the base module CP-2007 on the bottom plate, which is accessible after removing the bottom of the housing. We only handle the module without power supply!
Warnings / Cautions If you do not use a backup battery, connect terminals C1 and C4 with a wire!
Connection of power and system communication connector with 2.5 mm2 screw terminal
Connection of inputs / outputs connector with screw terminal 2.5 mm2
Ethernet RJ-45
Serial channels screw-type connector 9x 1.5 mm2
USB device connection type micro B
USB host connection type A
Module operation
Module configuration The module is operated, set and diagnosed from the MOSAIC programming environment. It is also possible to connect to the PLC using a web browser on port 8080. If the PLC has an IP address set eg (default address on port ETH1, port ETH2 has DHCP enabled), just enter the address in the form and the web browser displays the PLC configuration pages.
Commissioning The module is ready for operation after connection of the supply voltage. The MODE button is available on the module panel to display the currently set IP address of the Ethernet interface. Parameters of all interfaces are set in the Mosaic programming environment. The exact setup procedure is given in the TXV 004 50 documentation.
Module diagnostics The basic diagnostic system of the module is part of its standard software. It operates from module power on and operates independently of the user. Diagnostic error states of the module and connected peripheral modules of the assembly are signaled on the module display and are available for processing by the master system. For more information, see TXV 004 50.
Description The module does not require any maintenance under general installation conditions.
Notice Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Generally Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.

HW documentation


CP-2000 - Basic documentation (en)

2.75 MB, (EN)

User manuals


Foxtrot 2 - Serial communication (en)

2.25 MB, (EN, RU, DE)

Files for designers


Foxtrot 2 - library of elements in DXF and DWG formats, v. 2024/01.

20.49 MB

Foxtrot 2 - element library for SchemataCAD, v. 2024/01

6.79 MB

EC - Declaration of Conformity


Foxtrot 2 - EC Declaration of conformity (en)

590.15 kB, (EN, RU, DE, UA)
  • CP-2000 - The CP-2000 is the simplest version of the basic home installation module.  The base module is powered by a 24 VDC power supply. Both CIB branches (connector B) are supplied from the base module, which means that no CIB bus isolation modu...
  • Power dissipation of modules for calculation of switchboard heating - ...GT-1753 – 4 position axis control GT-1753 8,4 W TXN 120 00.11NDNN CP-2000 CP-2000 9,0 W TXN 120 05.11NSLN CP-2005, 6M, 128 KB databox, LTE, 6...
  • Foxtrot 2 - Shifts to two! - ...are penetrating into electrical installations with all the vehemence. The basic modules of the new series start with the CP-2000 number and there are a total of five variants in the first wave. The basic feature of the new generation is full com...
  • CP-2000 error - Hello. This error occurs every few days. CP-2000 firmware 5.3 2022-09-21 20:26:31.057759  Error E-92-40-01B110 Runtime error: Invalid pointer 2022-09-27 00:17:05.424706  Error E-92-40-01BF48 Runtime error: Invalid pointer 2022-09-30 21...
  • USSD comand sending with CP-2000 LTE - Hello! How can I send USSD code with CP-2000 LTE modem? I need it for reading of the credit amount of SIM card... I use GsmLib but there are no such tools in FBs for LTE.
  • CP-2000 and DMX - The CP-2000 central unit which submodul card should be that work with DMX? The function block only work with CH3 and CH4. Can't the SC-1101 be good?
  • Accessing SD data through web interface - Dear Support, I have a CP-2000 device that has been expanded with an SD card for data collection. I save data periodically to the SDC folder with Datalogger, but I can't access the files from the web interface, I can't refer to the folder like how...
  • UDP/TCP Packet Via VPN Network - Dear Support, I have a CP-2000 connected to a VPN network, I am trying to send a UDP/TCP Packet from a client to the PLC (UDP/TCP Server) but the connection is refused in the TCP server case and none in the UDP case. when I tried the same code on...
  • Bus thread cntRqst owerflow - Hello! Sometimes I have following error on CP-2000  Error E-B1-70-2001 IO error: Sub ITCL, lop 1, Bus TCL2, Bus thread cntRqst owerflow - ec =112 And I can`t understand  the reasons for this error. I have found this error subscribe in T...
  • PLCnet - Hello, I'm currently installing a system which uses several CP-2000 CPUs across multiple buildings, but they are connected to the same network. I would like to share and send data between the CPUs using PLCnet, but it seems to be unavailable (greye...
  • Cp1000 to cp2000 apple home bridge - Nastavení by mělo být následující: PlcComS 1 běží na, port 5010, IP adresa PLC je (CP-2000), HomeBridge 1 spolupracuje s PlcComS 1. PlcComS 2 běží na, port 5011 (CP-2000), IP adresa PLC je IP adresa CP-1000. HomeB...
  • TECO API - Actually, the application is as follows: AWS should set this token and save it in cp-2000, many ways to do this TCP/UDP connection or TECO API (I am trying both), and then cp-2000 will send an HTTPS request to the LWA OAuth server to refresh this to...
  • UDP/TCP Packet Via VPN Network - To resolve this issue we need more information. How is the CP-2000 connected to VPN? CP-2000 has possibility to natively connect to Wireguard VNP. Wireguard connection can be set up from a configuration web under Services > VPN. If the VPN is realis...