S-WS-0200R-LogusTXN 134 13

S-WS-0200R-Logus; Driver with short-travel control, 2 buttons/contacts 24V, (passively 1x LED red, 1x LED green, 1x internal sensor NTC 12k)

DI
DO
AI
AO
COM
SENSOR 2x button
1x NTC 12K
1x green LED
1x LED red
Picture Variant Variant description
S-WS-0200R-Logus
S-WS-0200R-Logus is a passive wall controller with
  • two short-way buttons under one flap,
  • with LED signaling 
  • with temperature sensor.
The controller is connected to a device that allows reading 2 inputs, controlling two binary outputs and measuring the resistance temperature sensor NTC 12k.
Order num. TXN 134 13
Teco code TXN 134 13
Categories CFox - LOGUS, Covers and devices
Tags -
Parameter des Temperatursensors
Temperature - Sensor type NTC 12k
Contact parameters
Maximum switching voltage 27 V DC
LED indication parameters
Maximum LED current 25 mA
Size and weight
Weight approx. 70 g
Product dimensions (width x height x depth) 86 × 86 × 38 mm
Operating conditions, product standards
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) IP10B
Operating areas Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device In the installation box on the wall
Working position Vertical
Type of operation (operating frequency) Continuous
Ambient operating temperatures 0 °C to + 55 °C
Operating relative humidity from 10 % up to 95 % without condensation
Operating atmospheric pressure min. 70 kPa (<3,000 m above sea level)
Storage temperatures –25 °C to +70 °C
Installation
Assembly description The module is mounted in a vertical position on a standard installation box with a spacing of fixing screws of 60 mm.
Method:
1. screw the support plate to the installation box (pay attention to the position)
2. connect the wires to the connector
3. attach the frame to the installation box and snap the module into place
4. click the fingerboards
Connection
Connection of inputs / outputs terminal block with spring clamp 0.15-0.5 mm2, push-in
Module connection The S-WS-0200R module is intended for connection to the module on the CIB bus C-IT-0504S (TXN 133 26) or C-IT-0908S (TXN 133 52). It can also be connected to other inputs and outputs while maintaining the polarity of the inputs and outputs. The LED outputs can also be switched by analog outputs, which supply 10 mA at 10 V. The configuration of inputs and outputs is performed in the superior module.
Maintenance
Description The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Warranty
Generally Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.

HW documentation

PDF

S-WS-0200R-Logus_ce.pdf Basic documentation

135.81 kB

Files for designers

ZIP

Foxtrot 2 - library of elements in DXF and DWG formats, v. 2024/01.

20.49 MB
KNI

Foxtrot 2 - element library for SchemataCAD, v. 2024/01

6.79 MB

No data available.

No data available.