CP-2091.11NDNNTXN 120 91.11NDNN

CP-2091; CPU, 2xETH100/10, 128kB dbox, LCD, 1x RS-485, 1xCIB, CH1-4, 8xAI/DI, 2xAI/DI/AO, 1x DI(230VAC), 2xAO/DO (PWM), 3xDO (PWM), 6xRO, 24VDC/230VAC

DI	6x DI/AI (HSC) 2x DI/AI 2x DI/AI/AO 1x DI (230 V AC)
DO	6x RO 3x DO (PWM) 2x DO/AO (PWM)
AI	6 AI/DI (HSC) see DI 2x AI/DI see DI 2x AI/DI/AO see AO
AO	2x DO/AO see DO 2x DI/AI/AO see DI
COM	2x ETH 4x CH1-4, slot for 2x submodule 1x RS-485 master 1x USB device 1x USB host 1x CIB master
SENSOR

Picture	Variant	Variant description
	CP-2091.11NDNN	Databox: 128 kB Processor: 1 core, ARMv7 792 MHz Display: OLED display large 55 x 13 mm

Basic modules CP-2091 are from the assortment of basic modules (ZM) of modular programmable automata of the Foxtrot 2 series.
Basic modules CP-2091,
- 8x multi-purpose inputs, each of which can be used either as an analog input or as a binary potential-free contact,
- 2x multi-purpose binary outputs (24V DC) / analog outputs (0-10V)
- one binary input 230 V AC,
- 3x binary outputs 24 V 0.5 A with optional PWM function
- 3x separate relay outputs 230 V AC/5A.
- 3x separate relay outputs 230 V AC/16A

The following interfaces are also available:
2x Ethernet,
up to 4x serial channels
1x master CIB installation bus for connecting external peripherals
2x master system buses TCL2 (SE-0140) intended for connecting expansion I/O modules that increase the total number of I/O

The CP-2091 basic module contains a basic LCD display with 4 x 20 characters and 6 user buttons.

Order num.	TXN 120 91.11NDNN
Teco code	TXN 120 91.11NDNN
Categories	Foxtrot 2 - Basic modules
Tags	-

System parameters of the central unit
Row of central unit	I
User program memory	1 MB
Memory for user variables / including RETAIN variables	320 kB/48 kB
Instruction length	4 Byte
Backup of program source code in PLC	Yes, optional in Mosaic
On-line program change in PLC	Yes, including I / O configuration change
DataBox - additional internal data memory	128/257 kB, optional
Memory for I / O data	64 KB / 64 KB
File system - Internal Drive in PLC	128 MB, journaling file system
File system - RAM disk PLC	16 MB
File System - USB Flash Drive	Supported
File system - Micro SD card	supported (except for variants with WLAN1)
Optional memory card slot	microSD - Card Slot (<= 1TB)
Cycle time per 1k of logic instructions	0,036 ms
Cycle time for 1k integer operations	0,044 ms
Cycle time for 1k floating point operations	0,043 ms
Development environment	Mosaic v2018.2 or higher
Programming languages	ST, IL, LD, FBD, SFC, CFC
RTC - Real time circuit	Yes
RTC - Backup time	typ. 500 hours
Integrated Web server	Yes
Integrated Datalogger	Yes
Access to PLC variables via web API	Yes
COM - Communication - IP/Ethernet
Ethernet 10/100 Mb (ETHx)	2
WLAN2 (external via USB host, optional)	1
LTE interface (LTEx, optional)	1
Available system modes on ETH and WLAN	UNI data exchange via UDP, TCP and SSL / TLS encryption support; PC EPSNET UDP / EPSNET TCP; PLC data sharing between PLCs (including CP-1xxx and CP-7xxx); PLD data sharing between PLC CP-2xxx and CP-8xxx including encryption
Available system modes on LTE	UNI data exchange via UDP, TCP and SSL / TLS encryption support; EPSNET UDP / EPSNET TCP
TCP / IP protocol	Yes
UDP protocol	Yes
HTTPS protocol	Yes
HTTP protocol	Yes
WebSocket protocol	Yes
Protocol MODBUS/TCP	Yes
SMTP protocol	Yes
IEC 60870-5-104 protocol	Yes
REST API	Yes
COM - USB
USB devices interface	1x micro-USB
USB host interface	1x USB-A
Available system modes on USB	PC
COM - Serial channels
max. number of serial channels that can be serviced at one time	10
max. number of internal serial channels	1
max. number of optional serial channels in the basic module	4
number of slots for optional submodules with interface (MR-013x)	2
max. number of expanding serial channels on the TCL2 bus	6 times on each TCL2 line
COM - Internal serial channels
Number of internal serial channels	1x RS-485
Available system modes on the internal serial channel	UNI general channel with any asynchronous communication PC communication with superior systems via EPSNET protocol MAS communication with EPSNET subordinate systems
Available communication speeds of system modes	1200 Bd, 2400 Bd, 4800 Bd, 9600 Bd, 14 400 Bd, 19 200 Bd, 28 800 Bd, 38 400 Bd, 57 600 Bd, 76 800 Bd, 115 200 Bd, 172 800 Bd, 230 400 Bd, 345 600 Bd
Galvanic separation of the internal serial channel	No
Receiver sensitivity	min. ±200 mV
Signal output level	typ. 3 V
Max. length of connected line	1200 m
Note on cable length	The maximum length applies to twisted and shielded cable and communication speed max. 120 kBd.
COM - Submodules with serial channels and optional interface
Number of slots for submodules with optional interface (MR-013x)	2
RS-232 serial channel on submodules	1x on MR-0130, 2x on MR-0134
Available communication speeds of modes on the RS-232 interface	1200 Bd, 2400 Bd, 4800 Bd, 9600 Bd, 14 400 Bd, 19 200 Bd, 28 800 Bd, 38 400 Bd, 57 600 Bd, 76 800 Bd, 115 200 Bd, 172 800 Bd
RS-485 serial channel on submodules	1x on MR-0131, 2x on MR-0133
Available communication speeds of modes on the RS-485 interface	1200 Bd, 2400 Bd, 4800 Bd, 9600 Bd, 14 400 Bd, 19 200 Bd, 28 800 Bd, 38 400 Bd, 57 600 Bd, 76 800 Bd, 115 200 Bd, 172 800 Bd, 230 400 Bd, 345 600 Bd
Available system modes on submodules MR-0130..MR-0134	UNI, PC, MAS
Profibus DP serial channel on submodules	1x on MR-0135
Available communication speeds of the PFB system mode	9600 Bd, 19 200 Bd, 93 750 Bd, 187 500 Bd
Profibus DP master protocol (<180 kbit/s)	PFB - Profibus DP Master (<180 kbit / s)
COM - Expansion communication modules on the TCL2 bus
RS-232 serial channel on modules	1x on SC-1101 (either RS-232 or RS-485)
RS-485 serial channel on modules	1x on SC-1101 (either RS-485 or RS-232)
Wireless M-Bus wireless communication channel on modules	1x on SC-1112.T
RFox2 wireless communication channel on modules	1x on SC-1111
Available communication modes on modules SC-1101, SC-1111, SC-1112	UNI - universal
Modbus RTU / ASCII master / slave protocol available on mode modules	UNI - Universal
CAN serial channel on modules	1x on SC-1102
Available communication modes on SC-1102 modules	CSJ - CAN bus connection
OpenTherm communication channel on modules	1x on UC-12044
MP-Bus communication channel on the modules	1x on UC-1203
COM - Expansion communication modules on the CIB bus - Common Installation Bus (R)
RFox2 wireless communication channel on modules	1x to C-RF-0001M-A; 1x RFox2 master, max. 10 addresses
DALI Communication interface on modules	1x and C-DL-0064M; 1x Master for 64 addresses
Wiegand communication interface on modules	1x on C-WG-0503S; 1x Master, formats 42 bits, 34bits, 26 bits, 40bits transparent
COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB master (100 mA)
CIB - Address range of one branch of the installation bus	32 CFox I/O modules
ITCL - internal system bus	Yes
ITCL - number of exchangeable submodules	2
ETCL - external system bus	1 (ETH1 or ETH2)
DI - Organization of binary inputs
Total number of binary inputs	11
Number of groups of binary inputs	2
Organization of binary inputs into groups	4x DI/AI (DI0/AI0-DI7/AI7) 6x DI/AI (HSC) (DI0/AI0-DI5/AI5) 2x DI/AI/AO (DI8/AI8/AO0-DI9/AI9/AO1) 1x DI 230 V AC (DI10)
DI - Parameters of binary inputs DC (group A)
Parameters valid for inputs on the terminals	DI0-DI9
Number of inputs in group	10
Common wire	minus
Input type	active (for dry contacts connection)
Combined input type	DI/AI Active, for sensing potential-free contacts and measuring resistance sensors
Galvanic isolation of inputs from internal/peripheral circuits	No
Diagnostics	indication of energized input by LED on module panel
Pulse input overload capacity	max. 30 V (t < 10 ms)
Input voltage for log. 0	+3 V DC min.
Input voltage for log. 1	1 V DC max.
Input current at log. 1 (typ.)	-1 mA
Delay from log. 0 to log. 1	500 μs
Delay from log. 1 to log. 0	500 μs
The minimum width of the captured pulse	500 μs
DI - Parameters of binary AC inputs
Parameters valid for AC inputs on the terminals	DI10
Total number of binary AC inputs	1
Number of groups of AC inputs	1
Number of AC inputs in group	1
Organization of binary inputs into groups	1x DI (DI10)
Diagnostics	Alarm of excited input on the panel
Input type	conventional switch
Galvanic isolation of internal circuits	Yes
Insulation voltage	3750 V AC
Input voltage for log. 0	0 v AC min., 50 V AC max.
Input voltage for log. 1	230 V AC typ. 95 V AC min., 260 V AC max.
Input current at log. 1 (typ.)	5 mA typ.
Delay from log. 0 to log. 1	max. 20 ms
Delay from log. 1 to log. 0	max. 20 ms
HSC - Counter input parameters
The parameters are valid for inputs	DI0-DI5
Special input functions	one-way counter
Counter: Input frequency / resolution	1 kHz
Pulse width	min. 500 μs
Delay from log. 0 per log. 1	500 μs
Delay from log. 1 per log. 0	500 μs
Range of registers	up to 32 bits, 0 to 4 294 967 296
HSC - PWM input parameters
Frequency range	10 Hz - 1 kHz
PWM input error	<1% (at 1 kHz)
Input resolution	10,4 μs (DI0), 0,2 μs (DI1)
DO/RO - Organization of binary outputs
Total number of binary outputs	11
Number of binary output groups	4
Organization of binary outputs into groups	6x RO (DO3-DO5, DO6-DO8 3x DO (PWM) (DO0-DO2) 2x DO/AO (DO9/AO2 - DO10/AO3)
DO - Parameters of binary transistor outputs (group A)
Parameters valid for the terminals	DO0-DO2, DO9-DO10
Number of transistor outputs	5
Number of output groups	2
Number of outputs in group	5
Organization of transistor outputs into groups	3x DO (DO0-DO2) + 2x DO (DO9-DO10)
Common group conductor	minus
Output type	MOSFET (Low-side switch)
Galvanic separation from internal circuits	No
Diagnostics	indication of energized output by LED on module panel
Switching voltage	5 - 30 V DC
Switching current, output load	0,5 A max.
Short-term output overload capacity	3 A max.
Output resistance	typ. 0,16 Ω, max. 0,4 Ω
Switching time	typ. 9 μs
Opening time	typ. 13 μs
Internal protection	overvoltage, short circuit and overheating protection
RO - Parameters of binary relay outputs (group A)
Parameters valid for the terminals	DO3-DO5
Number of relay outputs	3
Number of output groups	1
Number of outputs in group	3
Organization of relay outputs into groups	3x RO (DO3-DO5)
Output type	electromechanical relay, unprotected output
Contact type	NO - Normally Open
Galvanic separation from internal circuits	Yes
Diagnose	Alarm signaling on panel module
Switching current	3 A max., 100 mA min.
Switching voltage	250 V AC max., 5 V AC min., 30V DC max.
Switching power	1250 VA max. for AC, 90 W max. for DC
Short-term output overload - inrush	4 A max.
Current through common clamp	10 A max.
Contact closing time	typ. 10 ms
Contact opening time	typ. 4 ms
Limit values of switched resistive load	max. 3A at 30 V DC or 230 V AC
Switching inductive load limits DC13	max. 3 A at 30 V DC
Switching inductive load limits AC15	max. 3 A at 230 V AC
Switching frequency without load	max. 300 switching / min.
Switching frequency with rated load	max. 20 switching / min.
Mechanical life	min. 5,000,000 cycles
Electrical life at maximum resistive load	min. 100,000 cycles
Electrical life at maximum load inductive DC13	min. 100,000 cycles
Electrical life at maximum load inductive AC15	min. 100,000 cycles
Short-circuit protection	No
Treatment of inductive load	External RC element, varistor (AC), diode (DC)
Insulation voltage between outputs and internal circuits	3750 V AC
Isolation voltage between groups of outputs to each other	3750 V AC
RO - Parameters of binary relay outputs (group B)
Parameters valid for the terminals	DO6-DO8
Number of relay outputs	3
Number of output groups	3
Number of outputs in group	1
Organization of relay outputs into groups	1x RO (DO6) + 1x RO (DO7) +1x RO (DO8)
Output type	electromechanical relay, unprotected output
Contact type	NO - Normally Open
Galvanic separation from internal circuits	Yes
Galvanic isolation between groups	Yes
Diagnose	Alarm signaling on panel module
Switching current	10 A max., 100 mA min.
Switching voltage	max. 250 V AC; max. 30 V DC; min. 5 V
Short-circuit protection	No
Short-term output overload	10A max.
Current through common clamp	10 A max.
Contact closing time	typ. 10 ms
Contact opening time	typ. 4 ms
Limit values of switched resistive load	max. 10A at 30 V DC or 230 V AC
Switching inductive load limits DC13	max. 10 A at 30 V
Switching inductive load limits AC15	max. 10 A at 230 V AC
Switching frequency without load	max. 300 switching / min.
Switching frequency with rated load	max. 6 switching / min
Mechanical life	min. 5,000,000 cycles
Electrical life at maximum resistive load	min. 100,000 cycles
Electrical life at maximum load inductive DC13	min. 100,000 cycles
Electrical life at maximum load inductive AC15	min. 100,000 cycles
Treatment of inductive load	External RC element, varistor (AC), diode (DC)
Insulation voltage between outputs and internal circuits	3750 V AC
Isolation voltage between groups of outputs to each other	3750 V AC
AI - Organization of analog inputs
Total number of analog inputs	10
Number of inputs per group	10
Number of analog input groups	1
Organization of analog inputs into groups	10 (DI0/AI0-DI9/AI9)
Input type	With common clamp
Common wire	Minus
Galvanic separation from internal circuits	No
Diagnostics	overload signaling in status word
External power supply	No
Digital resolution	12 bit
Converter type	Approximation
conversion time	20 μs
Operating modes	periodic input sensing
Filtration	low pass filter, digital comb filter 50/60 Hz
Insulation potential	500 V DC between input and internal circuits
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals	DI0/AI0 - DI9/AI9
Passive sensor	Pt1000, W100 = 1,385 (-90 to +400 ° C)
Passive sensor	Pt1000, W100 = 1,391 (-90 to +400 ° C)
Passive sensor	Ni1000, W100 = 1,500 (–60 to +200 ° C)
Passive sensor	Ni1000, W100 = 1.617 (-60 to +200 ° C)
Passive sensor	Resistance transmitter 0-2 kOhm
Passive sensor	KTY81-121; PTC thermistor (-55 to + 125 °C)
Input impedance in signal range RTD	> 4 kΩ
Resistance measurement error - maximum error at 25 ° C	± 0.5% of full scale
Resistance measurement error - temperature coefficient	± 0.05% of full scale / K
Resistance measurement error - non-linearity	± 0.09% of full scale
Resistance measurement error - repeatability at steady conditions	0.07% of full scale
Max. permissible permanent overload of analog input (without damage)	–20 to +30 V (each AI terminal against AGND)
Open input detection	No
Detection of disconnected sensor	yes, in status word, range overflow
AO - Analog output parameters
The number of groups of analogue outputs	1
Number of outputs in group	4
Organization of outputs in groups	2x (DI8/AI8/AO0-DI9/AI9/AO1) + 2x AO (DO9/AO2-DO10/AO3)
Parameters valid for the terminals	AO0-AO3
Common wire of group	minus
Galvanic isolation from internal circuits	No
Output type	active voltage output
Max. permissible permanent overload (without damage)	± 20 V, each terminal against AGND
Converter resolution	12 bit
conversion time	10 μs
Analog output error - maximum error at 25 ° C	± 2% of full scale
Analog output error - temperature coefficient	± 0.3% of full scale / K
Analog output error - linearity	± 0.7% of full scale
Analog output error - repeatability under steady state conditions	± 0.5% of full scale
External power supply	No
Voltage output - voltage	0 - 10,5 V
Voltage output - Resolution 1 LSB	20,5 mV
Voltage output - maximum output current	10 mA
Power supply
Supply voltage, tolerances	24 V DC, +25%, -15%, SELV
Auxiliary power supply - voltage	Optional: from 230 V AC mains, 40-60 Hz
Maximum power input	10 W
Module thermal/power loss	12 W
Internal protection	Yes, PTC reversible fuse
Power supply from ETH, passive PoE - input (appliance)	ETH1/Power In
Power supply from ETH, passive PoE - output (source)	ETH2 / Power out, jumper configuration
Power supply from ETH, passive PoE - injector parameters	24 V DC, 1A
Size and weight
Weight approx.	300 g
Product dimensions (width x height x depth)	158 x 90 x 58 mm
Module width in multiples of M (17.5 mm)	9M
Operating conditions, product standards
Product standard	ČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units
Protection class of electrical object	II, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP20
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	Module on DIN rail
Working position	Vertical
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	-20 °C to + 55 °C
Operating temperature maximum (° C)	+55°C
Operating temperature minimum (° C)	-20°C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	B, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015)
Emmisions - note	In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action.
Electromagnetic compatibility / Immunity	min. as required by EN 61131-2: 2007
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	The module is packed in a paper box according to the internal packing instructions. The package includes the following documentation. The outer packaging is carried out according to the scope of the order and the method of transport to the transport a package bearing the transport labels and other particulars necessary for transport. Transport from the manufacturer is carried out in the manner agreed upon when ordering. Product transport the customer's own means must be carried out by covered means of transport, in the specified position label on the packaging. The box must be stowed so as to prevent spontaneous movement a damage to the outer packaging. The product must not be exposed to direct weathering during transport and storage influences. Transport is allowed at temperatures from -25 ° C to +70 ° C, relative humidity 10% up to 95% (non-condensing) and a minimum atmospheric pressure of more than 70 kPa. Storage of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Installation
Assembly description	Switchboard mounting
Assembly description	The basic module is mounted vertically on the U-rail ČSN EN 50022. The installation of the assembly (basic module and peripheral modules, if applicable) is performed according to TXV 004 50.
Exchangeable submodules	The optional MR-013x submodules of the serial interface are mounted in the base module CP-2091 on the bottom plate, which is accessible after removing the bottom of the housing. We only handle the module without power supply!
Connection
Connection of power and system communication	connector with 2.5 mm2 screw terminal
Connection of inputs / outputs	connector with screw terminal 2.5 mm2
Ethernet	RJ-45
Serial channels	screw-type connector 9x 1.5 mm2
USB device connection	type micro B
USB host connection	type A
Module operation
Module configuration	The module is operated, set up and diagnosed from the Mosaic development environment.
Module diagnostics	The basic diagnostic system of the module is a part of its standard software. It operates from module power on and operates independently of the user. Diagnostic error states of the module and connected peripheral modules of the assembly are signaled
Maintenance
Description	The module does not require any maintenance under general installation conditions.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.

HW documentation

PDF

Basic documentation - en

2.34 MB, (EN)

User manuals

PDF

Foxtrot 2 - Serial communication (en)

2.25 MB, (EN, RU, DE)

Files for designers

ZIP

Foxtrot 2 - library of elements in DXF and DWG formats, v. 2024/01.

20.49 MB

KNI

Foxtrot 2 - element library for SchemataCAD, v. 2024/01

6.79 MB

EC - Declaration of Conformity

PDF

Foxtrot 2 - EC Declaration of conformity (en)

590.59 kB, (EN, RU, DE, UA)

No data available.

CP-2091.11NDNNTXN 120 91.11NDNN

HW documentation

Basic documentation - en

User manuals

Foxtrot 2 - Serial communication (en)

Files for designers

Foxtrot 2 - library of elements in DXF and DWG formats, v. 2024/01.

Foxtrot 2 - element library for SchemataCAD, v. 2024/01

EC - Declaration of Conformity

Foxtrot 2 - EC Declaration of conformity (en)

MR-0130, 1x RS-232

MR-0131, 1x RS-485

MR-0133, 2x RS-485

MR-0134, 2x RS-232

MR-0135, 1x RS-485, Profibus master

MR-0136, 1x CAN, with its own power supply, galvanic isolation

SE-0140, TCL2 Master - Expander

Confirmation