C-OR-0202BTXN 133 02

C-OR-0202B; CIB, 2x AI/DI; 2x RO NO/NC contacts; 230VAC/16A

DI 2x AI / DI see AI
DO 2x RO 16A, NO / NC
AI 2x AI / DI see DI
AO
COM 1x CIB slave
SENSOR
Picture Variant Variant description
C-OR-0202B
C-OR-0202M is a module on the CIB bus that it contains
2 relay outputs with changeover contact 16A NO/NC, each separately connected to the terminal board
2 analog / binary inputs for connecting temperature sensors or potential-free contacts.

It is mounted in any position in the installation box under the lid or under the device in the installation box.
It is powered from the CIB bus
Order num. TXN 133 02
Teco code TXN 133 02
Categories CFox - Built-in modules
Tags -
COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus 1x CIB slave
DO/RO - Organization of binary outputs
Total number of binary outputs 2
Number of binary output groups 2
RO - Parameters of binary relay outputs (group A)
Parameters valid for the terminals DO1, DO2
Number of relay outputs 2
Number of output groups 2
Number of outputs in group 1
Organization of relay outputs into groups 1x (D01) + 1x (DO2)
Output type electromechanical relay, unprotected output
Contact type NO / NC changeover contact
Galvanic separation from internal circuits Yes
Galvanic isolation between groups Yes
Diagnose Alarm signaling on panel module
Switching current 16 A max. NO/10 A max NC, 100 mA min.
Switching voltage 300 V max., 5 V min.
Switching power 4000 VA max., 384 W max.
Short-term output overload - inrush 80 A max. (20 ms max.)
Contact closing time typ. 15 ms
Contact opening time typ. 5ms
Mechanical life min. 20 000 000 cycles
Electrical life at rated load min. 10,000 switchings (inrush 80 A)
Electrical life at maximum resistive load min. 50,000 cycles
Short-circuit protection No
Treatment of inductive load External RC element, varistor (AC), diode (DC)
Insulation voltage between outputs and internal circuits 4000 V AC
Isolation voltage between groups of outputs to each other work isolation
Insulation voltage between contacts 1000 V AC
AI - Organization of analog inputs
Total number of analog inputs 2
Number of inputs per group 1
Number of analog input groups 2
Organization of analog inputs into groups 1x (AI1) + 1x (AI2)
Input type With common clamp
Common wire GND terminal
Galvanic separation from internal circuits No
Diagnostics overload signaling in status word
Digital resolution 10 bit
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals AI1, AI2
Passive sensor Pt1000, W100 = 1,385 (-90 to +400 ° C)
Passive sensor Pt1000, W100 = 1,391 (-90 to +400 ° C)
Passive sensor Ni1000, W100 = 1,500 (–60 to +200 ° C)
Passive sensor Ni1000, W100 = 1.617 (-60 to +200 ° C)
Passive sensor Resistance transmitter 0-160 kOhm
Passive sensor KTY81-121; PTC thermistor (-55 to + 125 °C)
Passive sensor NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
DI: Voltage-free contact 0 when> 1.5 kOhm, 1 when <0.5 kOhm
DI: Balanced resistance input 2x 1k1 (tamper/0/1/tamper)
Resistance measurement error - maximum error at 25 ° C ± 0.5% of full scale
Power supply
Supply voltage, tolerances 24/27 V DC from CIB bus
Maximum power input 1,5 W
Power supply from CIB - maximum current consumption (mA) 50 mA
Galvanic separation of power supply from internal circuits No
Power supply from CIB - Galvanic separation of power supply from internal circuits No
Power supply from CIB - internal protection Yes, returnable fuse
Size and weight
Weight approx. 75 g
Product dimensions (width x height x depth) 50 x 50 x 30 mm
Operating conditions, product standards
Product standard ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)
Protection class of electrical object III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) IP20
Operating areas Normal according to ČSN 33 2000-1: 2003 (IEC 364-1: 1992 mod)
Degree of pollution 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation I, according to ČSN EN 60664-1 ed_2:2008 (idt IEC 60641-1:2007)
Type of device In the installation box, under the cover
Working position Any
Type of operation (operating frequency) Continuous
Ambient operating temperatures -10 °C to + 55 °C
Operating temperature maximum (° C) +55°C
Operating temperature minimum (° C) -10°C
Operating relative humidity from 10 % up to 95 % without condensation
Operating atmospheric pressure min. 70 kPa (<3,000 m above sea level)
Storage temperatures –25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission B, according to EN 55022: 1999 (mod CISPR22: 1997)
Emmisions - note In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action.
Electromagnetic compatibility / Immunity min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Installation
Assembly description The module is mounted in a vertical position on the U-rail ČSN EN 50022. Installation of the assembly (basic module and possibly peripheral modules) is performed according to TXV 004 13.
Connection
Connection of power and system communication terminal block with screw terminal 1.5 mm2
Specific I / O Relay outputs
Connection of specific I / O Insulated wires with sleeve
Cross-section of connected wires stranded (max) 2,5 mm2
Module installation tools (-) 3 mm, flat screwdriver
Module connection The module has a CIB bus and 2 inputs are connected to screw terminals, the changeover contacts of the relay are connected by means of insulated conductors with a length of approx. 80 mm terminated in sockets.

The CIB bus master is a FOXTROT base unit or module, such as the CF-1141. The maximum number of modules on a line is limited by taking a module from the line. For more information, see the Peripheral Modules on the CIB TXV 004 13 manual. An example of the module connection is shown in the following figure.
Module operation
Commissioning The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module.
Module diagnostics The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment. When the power is turned on, the RUN LED lights up green, after communication is established, it starts flashing. The switching status of the relay is indicated by a green LED.
Maintenance
Description The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Notice Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.

HW documentation

PDF

C-OR-0202B - Basic documentation

990.05 kB, (EN)

User manuals

PDF

Peripheral modules on the CIB Common Installation Bus(R) (en), TXV00413_02

13.94 MB, (EN, RU, DE, UA)

Files for designers

ZIP

Foxtrot 2 - library of elements in DXF and DWG formats, v. 2024/01.

20.49 MB
KNI

Foxtrot 2 - element library for SchemataCAD, v. 2024/01

6.79 MB

EC - Declaration of Conformity

PDF

Foxtrot - EC Declaration of conformity

295.20 kB, (EN, RU, DE, UA)
  • C-OR-0202B, relay outputs and analogue inputs - The C-OR-0202B module is equipped with 2 relays with a switching contact, each is separately terminated with insulated conductors, their length is approx. 100mm. Continuous current in each 16 A output, switching inrush current up to 80A (maximum 20...
  • Control of asynchronous motors for blinds, awnings, C-OR-0202B - ...hielding element in the installation box. Fig.1    Example of connection of blind motor control by module C-OR-0202B Notes: Relay outputs with mutual blocking of switching of both outputs, when DO1 is closed the mo...
  • Electric underfloor heating - ...relay outputs in accordance with the switching power. You can make use of the relay output directly to the flush box ( C-OR-0202B with a possibility of simultaneously measuring the floor temperature), or the C-OR-0008M module, which ca...
  • 16 A relay (80 A switching current), the CFox and RFox peripheral modules - These relays are fitted in e.g. the C-OR-0008M , C-OR-0202B , R-OR-0001B peripheral modules, and others (see the information on the individual modules ). The NO contact is designed as increased (inrush current 80 A), the NC con...
  • The control of Schüco windows - ...n be used for the control; it is appropriate to use two separate, mutually independent outputs - see the example with the C-OR-0202B module. Fig. 1. Connecting a Schüco TipTronic window to the C-OR-0202B module   N...
  • Connecting the LineaMatic sliding gate - ...partial opening of the gate (about 1.5m) for the passage of people. To control the gate it is recommended to use the C-OR-0202B module located at the gate. The module inputs can be used e.g. for the local control buttons, or for connecting...
  • Control of direct current motors for roller blinds - ...tage (motors for interior blinds, and such like), we recommend to use relay outputs with a switching contact, such as the C-OR-0202B . Fig. 1. An example of wiring the control of DC motor for roller blinds by the C-OR-0202B module...
  • Control of socket circuits and sockets - ...puts of the C-HM-1121M module and their RFox variants), see this article placed in the installation box C-OR-0202B and  R-OR-0001B , see  this article For switching 3f sockets, usually with a higher rated...
  • Switching of LED lighting, light bulbs, fluorescent lamps, etc. - ...ith short-term switching current up to 80 A C-OR-0008M 8 relay outputs with short-term switching current up to 80 A C-OR-0202B 2 relay outputs with short-term switching current up to 80 A C-HM-1113M 1 relay output with short-term switc...
  • Valves for controlling water (the main water valve, etc.) - The valve designed to control the distribution of drinking water (e.g. the main water valve), automatic control of irrigation systems, etc. Its design is also suitable for the so-called hard water. It is a good replacement of solenoids and pneumatic...

No data available.