English
R-KF-0500T-A, RF keychainTXN 132 08.A
R-KF-0500T-A; RFox2, keyfob, 5 buttons, radio type A
| DI | 5x button |
|---|---|
| DO | |
| AI | |
| AO | |
| COM | 1x RFox2 slave |
| SENSOR |
| Picture | Variant | Variant description |
|---|---|---|
|
R-KF-0500T-A, RF keychain |
R-KF-0500T-A; RFox2, keyfob, 5 buttons, radio type A
| Order num. | TXN 132 08.A |
|---|---|
| Teco code | TXN 132 08.A |
| Categories | RFox2 - Interior Modules |
| Tags | - |
| COM - Wireless network | |
|---|---|
| RFox2 wireless network | RFox2 Slave |
| Communication frequency band | 868,1 MHz |
| Transmission power | +14 dBm |
| Input sensitivity | –108 dBm |
| Modulation type | 2-GFSK |
| Communication speed | 50 kbps |
| Size and weight | |
| Weight approx. | 7 g |
| Product dimensions (width x height x depth) | 70 × 35 × 15 mm |
| Operating conditions, product standards | |
| Product standard | ČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units |
| Operating areas | Normal according to ČSN 33 2000-1: 2003 (IEC 364-1: 1992 mod) |
| Degree of pollution | 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007) |
| Working position | Any |
| Ambient operating temperatures | -20 °C to + 55 °C |
| Operating relative humidity | from 10 % up to 95 % without condensation |
| Operating atmospheric pressure | min. 70 kPa (<3,000 m above sea level) |
| Storage temperatures | –25 °C to +70 °C |
| Electromagnetic compatibility, Mechanical endurance | |
| Electromagnetic compatibility / Emission | B, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015) |
| Electromagnetic compatibility / Immunity | min. as required by EN 61131-2: 2007 |
| Sinusoidal vibration endurance | 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.) |
| Maintenance | |
| Instructions |
The module does not require any maintenance if the general conditions of use are observed. The battery is replaced after separating the lower part of the plastic cover of the keychain from the upper part using a suitable tool (screwdriver). The position of the latches is indicated in the following figure by arrows. Slide the discharged battery out of the holder and insert a new battery, paying attention to the correct polarity. Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch components on the printed circuit board without protective measures. |
| Warranty | |
| Generally | Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s. |
| Notice | You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change. |
HW documentation
R-KF-0500T-A - Basic documentation
167.96 kB
Files for designers
Foxtrot 2 - library of elements in DXF and DWG formats, v. 2024/01.
20.49 MB
Foxtrot 2 - element library for SchemataCAD, v. 2024/01
6.79 MB
No data available.
No data available.